This way we get pin muxing out of plat-omap and can convert H4 to use the
new mux functions.
Note that it should be safe to assume we can mux all the keypad pins
except on H4 which may have Menelaus connected.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move omap2 FS USB platform init code into mach-omap2/usb-fs.c. This will
allow further work later on to use omap hwmod for initializing the
device.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We want to split old FS USB platform init code and stop doing pin multiplexing
under plat-omap. First move 24xx specific init code into omap2_usb[012]_init
functions.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The function prefix "omap2_iommu_" indicates that the prefixed
function belongs to "omap2_iommu_ops" to provide iommu basic
functionalities for the above layers. It's better to avoid the
prefixed function called in the same prefixed ones internally, like
nested here. Now "iommu_disable" is called just after fault_isr() in
the above layer. This is a little bit more sensible to keep the
consistency of module layers.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
In order to enable TLB miss interrupt, the TWL should be
disabled. This patch provides the functionality to get the
MMU fault interrupt for a TLB miss in the cases where the
users are working with the locked TLB entries and with TWL
disabled.
New interface is added to select twl and to enable TLB miss
interrupt.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Ramesh Gupta <grgupta@ti.com>
Signed-off-by: Hiroshi Doyu <Hiroshi.DOYU@nokia.com>
The addition of the new debounce code (commit
168ef3d9a5) broke the auto-disable of
debounce clocks on idle by forgetting to update the debounce clock
enable mask.
Add back the updating of bank->dbck_enable_mask so debounce clocks are
auto-disabled.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The kernel timer queue is being run currently from a GP timer running in a one
shot mode, which works in a way that when it expires, it will also stop.
Usually during this situation, the interrupt handler will ack the interrupt,
load a new value to the timer and start it again. During suspend, the
situation is slightly different, as we disable interrupts just before
timekeeping is suspended, which leaves a small window where the timer can
expire before it is stopped, and will leave the interrupt flag pending.
This pending interrupt will prevent ARM sleep entry, thus now we ack it always
when we are attempting to stop a timer.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: removed the ifdef to make the patch cover omap1 also]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The memory allocated for sgt structure is not freed on error
when sg_alloc_table is called in sgtable_alloc().
Signed-off-by: Satish Kumar <x0124230@ti.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Cc: Vimal Singh <vimal.newwork@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgen <tony@atomide.com>
Sicne the platform data's buffer_size now holds the full size
of the FIFO, there is no longer need to handle the ports
differently.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Use the actual FIFO size in words as buffer_size on OMAP3.
Change the threshold configuration to use 1 based numbering, when
specifying the allowed threshold maximum or the McBSP threshold value.
Set the default maximum threshold to (buffer_size - 0x10) intialy.
>From users of McBSP, now it is expected to use this method.
Asking for threshold 1 means that the value written to threshold registers
are going to be 0, which means 1 word threshold.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Users of McBSP can use the omap_mcbsp_get_fifo_size function to query
the size of the McBSP FIFO.
The function will return the FIFO size in words (the HW maximum).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolsfonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Nobody uses that anymore, so remove and expect drivers to use the gpiolib
implementation.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP supports debouncing of gpio lines, implement the method using
gpiolib.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (113 commits)
omap4: Add support for i2c init
omap: Fix i2c platform init code for omap4
OMAP2 clock: fix recursive spinlock attempt when CONFIG_CPU_FREQ=y
OMAP powerdomain, hwmod, omap_device: add some credits
OMAP4 powerdomain: Support LOWPOWERSTATECHANGE for powerdomains
OMAP3 clock: add support for setting the divider for sys_clkout2 using clk_set_rate
OMAP4 powerdomain: Fix pwrsts flags for ALWAYS ON domains
OMAP: timers: Fix clock source names for OMAP4
OMAP4 clock: Support clk_set_parent
OMAP4: PRCM: Add offset defines for all CM registers
OMAP4: PRCM: Add offset defines for all PRM registers
OMAP4: PRCM: Remove duplicate definition of base addresses
OMAP4: PRM: Remove MPU internal code name and apply PRCM naming convention
OMAP4: CM: Remove non-functional registers in ES1.0
OMAP: hwmod: Replace WARN by pr_warning for clockdomain check
OMAP: hwmod: Rename hwmod name for the MPU
OMAP: hwmod: Do not exit the iteration if one clock init failed
OMAP: hwmod: Replace WARN by pr_warning if clock lookup failed
OMAP: hwmod: Remove IS_ERR check with omap_clk_get_by_name return value
OMAP: hwmod: Fix wrong pointer iteration in oh->slaves
...
Add platform init code for the OMAP3 OHCI driver.
Also, configure padconf settings for OMAP3 depending
on which port mode is used.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
EXTVBUS programming is required by OMAP3EVM REV >=E to supply 500mA
power so adding a flag which can be used by musb driver to program
EXTVBUS.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for i2c init for omap4.
This patch is based on and earlier patch by
Santosh Shilimkar <santosh.shilimkar@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add separate omap_i2c_add_bus functions for mach-omap1
and mach-omap2. Make the mach-omap2 init set the interrupt
dynamically to support.
This is needed to add support for omap4 in a way that
works with multi-omap builds. This will eventually get
fixed in a generic way with the omap hwmods.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add some missing credits for people who have contributed significant features
or fixes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Thara Gopinath <thara@ti.com>
Some powerdomains in OMAP4 support a direct transition from one sleep
state to another deeper sleep state without having to wakeup the
powerdomain. This patch adds an api in the powerdomain framework to
set the LOWPOWERSTATECHANGE bit in PWRSTCTRL register.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The pwrsts flag for ALWAYS ON domains like always_on_core_pwrdm
and wkup_pwrdm is wrongly populated with the define for a
powerdomain power state, instead of the allowable state
bitfields.
This causes a few api's to fail sensing invalid pwrst
requested.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The clock sources for timers on OMAP4 (system clock and 32k
clock) have their names wronly populated.
This patch fixes them so the omap_dm_timer_set_source
does not fail anymore.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Remove the hack put in place while clock framework was still not in
place for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The MPU subsystem was named based on internal code name (CHIRON).
This patch will remove all the occurences of the chiron name
are replace it with PRCM_MPU in order to differentiate
the MPU local PRCM to the global one.
Remove PDA_ from PRCM_MPU registers names to stick to the global
PRM naming convention.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Some initiator modules in OMAP2 & 3 does not have IDLEST bit,
in that case we cannot detect the module readiness by
polling that bit and must exist the function immediately
assuming that the module is ready.
The previous flag was affected to the OCP interface. While it is
technically true that the idlest is related to the L4 slave
interface of the module, the PRCM status belong to the module.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Accessing the clkctrl register using offset of module & device is hard
to do in OMAP4 due to the way the CM1, CM2, PRM and PRCM_MPU are located
in the address space. There is no common base address anymore for all the
CM registers.
The easiest way to handle that on OMAP4 is to provide the absolute address
of the XXX_CLKCTRL register per hwmod.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Clean up comment style, remove unnecessary includes, and resolve some
checkpatch warnings in plat-omap/clock.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Rename the RATE_IN_343X clksel_rate.rate flag to be RATE_IN_3XXX, to reflect
that these rates are valid on all OMAP3 platforms, not just 343X.
Also rename the RATE_IN_OMAP3430ES2 clksel_rate.rate flag to be
RATE_IN_OMAP3430ES2PLUS, to reflect that these flags are valid on all
OMAP3 platforms after 3430ES2.
This patch should not result in any functional changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
The DEFAULT_RATE clksel_rate flag is essentially useless. It was set
on some of the lowest divisors, which, when switching to a much
higher-rate parent, could have potentially resulted in rates that
exceeded the hardware specifications for downstream clocks in the
window between the clk_set_parent(), and a subsequent clk_set_rate().
It seems much safer to just remove the flag and always use the highest
available divisor (resulting in the lowest possible rate) after the
switch, and this patch does so.
Ideally, it would be best to first attempt to switch to a divisor that
matches the clock's rate with the previous parent, if at all possible.
But that is a project for some other day or some other person. The
parent changing code is rarely used.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP4, MMC1 PBIAS and its associated IO is software-controlled
by CONTROL_PBIAS and CONTROL_MMC1 registers. This patch adds PBIAS
configuration for MMC1 Controller during power-ON and power-OFF
of regulator.
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Access to some of the OMAP4 GPIO registers are not properly handled.
This patch fixes it.
This patch is tested on 3430SDP and 4430SDP boards
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves OMAP4 soc specific code from 4430sdp board file.
The change is necessary so that newer board support can be added
with minimal changes. This will be also problematic for
multi-board, multi-omap builds.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517 don't have the register OMAP343X_CONTROL_PBIAS_LITE and the regulators
like "vmmc", so we set a noop "set_power" function for it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Multi line comments are fixed as per CodingStyle
guidelines.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If we are softbooting another kernel using kexec, DMA controller state is not
known when we are performing omap_init_dma(). It is possible that some DMA
channels are already active. For example after kexec we get:
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
<4>IRQ 0020 for non-allocated DMAchannel 5
To prevent any weird things happening, we disable all channel interrupts during
init.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (250 commits)
ALSA: hda: Storage class should be before const qualifier
ASoC: tpa6130a2: Remove CPVSS and HPVdd supplies
ASoC: tpa6130a2: Define output pins with SND_SOC_DAPM_OUTPUT
ASoC: sdp4430 - add sdp4430 pcm ops to DAI.
ASoC: TWL6040: Enable earphone path in codec
ASoC: SDP4430: Add support for Earphone speaker
ASoC: SDP4430: Add sdp4430 machine driver
ASoC: tlv320dac33: Avoid powering off while in BIAS_OFF
ASoC: tlv320dac33: Use dev_dbg in dac33_hard_power function
ALSA: sound/pci/asihpi: Use kzalloc
ALSA: hdmi - dont fail on extra nodes
ALSA: intelhdmi - add id for the CougarPoint chipset
ALSA: intelhdmi - user friendly codec name
ALSA: intelhdmi - add dependency on SND_DYNAMIC_MINORS
ALSA: asihpi: incorrect range check
ALSA: asihpi: testing the wrong variable
ALSA: es1688: add pedantic range checks
ARM: McBSP: Add support for omap4 in McBSP driver
ARM: McBSP: Fix request for irq in OMAP4
OMAP: McBSP: Add 32-bit mode support
...
While waiting for completion of the i2c transfer, the
MPU could hit OFF mode and cause several msecs of
delay that made i2c transfers fail more often. The
extra delays and subsequent re-trys cause i2c clocks
to be active more often. This has also an negative
effect on power consumption.
Created a mechanism for passing and using the
constraint setting function in driver code. The used
mpu wake up latency constraints are now set individually
per bus, and they are calculated based on clock rate
and fifo size.
Thanks to Jarkko Nikula, Moiz Sonasath, Paul Walmsley,
and Nishanth Menon for tuning out the details of
this patch.
Updates by Kevin as requested by Tony:
- Remove omap_set_i2c_constraint_func() in favor of conditionally
adding the flag in omap_i2c_add_bus() in order to keep all the OMAP
conditional checking in a single location.
- Update set_mpu_wkup_lat prototypes to match OMAP PM layer so
OMAP PM function can be used directly in pdata.
Cc: Moiz Sonasath <m-sonasath@ti.com>
Cc: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
McBSP module in OMAP4 needs to be able to set its tx/rx threshold
and enable the transmitter/receiver when starting an audio stream.
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Signed-off-by: Margarita Olaya Cabrera <magi.olaya@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
In OMAP4, there is only one irq line for TX and RX paths. Use
the correct irq line to avoid errors at runtime.
Also, request irq line only once (instead of requesting for TX
and RX).
Signed-off-by: Jorge Eduardo Candelaria <jorge.candelaria@ti.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This rejects unaligned device virtual address('da') and physical
address('pa') and informs error to caller when a page table entry is
set. Otherwise, a wrong address can be used by IO device.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Hari Kanigeri <h-kanigeri2@ti.com>
Searching avaialable spaces should be stopped as soon as it turns out
that there's no possibility with the rest of it.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Inserting a gap page between IOVMAs could detect an override on other
IOVMA with iommu fault. This was originally suggested by Sakari Ailus
and based on the work and comment by David Cohen.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: David Cohen <david.cohen@nokia.com>
Cc: Sakari Ailus <Sakari.Ailus@nokia.com>
This CONFIG_OMAP_IOMMU_DEBUG option cannot be selected because it's
not visible on menu. Make this option selectable.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
There are some places to scan iotlb entries. This iteration macro
could make these code a bit simpler with proceeding iotlb entries
transparently.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Tested-by: Hari Kanigeri <h-kanigeri2@ti.com>
This patch adds TLB preservation support to IOMMU module
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch provides the iommu support for OMAP4 co-processors.
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
The generic gpiolib provides a debugfs interface to GPIOs which
provides identical (but nicer looking) data as the OMAP specific one.
This patch completely drops the OMAP specific interface
(/debug/omap_gpio) in favor of using the generic one (/debug/gpio.)
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
setwkuena and setdataout are covered already by wake_en and dataout fields.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Ensure GPIO debounce clocks are disabled when idle. Otherwise,
clocks will prevent PER powerdomain from entering retention.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, the GPIO 'prepare' hook is only called when going to
off-mode, while the function is called 'prepare_for_retention.' This
patch renames the function to 'prepare_for_idle' and calls it for any
powersate != PWRDM_POWER_ON passing in the powerstate.
The hook itself is then responsible for doing various preparation
based on the powerstate.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
According to the GPIO 'Wakeup and Interrupt' section of the TRM[1],
wake-up requests can only be generated on edge transitions.
Also for OMAP3, only edge GPIOs may lose interrupts when PER enters
RET/OFF state, this is addressed by gpio prepare|resume idle functions
[1] Section 25.5.3.1 OMAP34xx_ES3.1_TRM_V_Q
Signed-off-by: Chunqiu Wang <cqwang@motorola.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Off mode is now using the omap2 retention fix code for scanning GPIOs
during off-mode transitions. All the *non_wakeup_gpios variables
are now used for off-mode transition tracking on OMAP3. This patch fixes
cases where GPIO state changes are missed during off-mode.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Several ARM platforms/machines that use FIQ define their value of FIQ_START.
Since FIQ is not implemented for OMAP yet, this definition is missing from
OMAP header files.
Put an arbitrary value for FIQ_START into plat/irqs.h for OMAP. Even if not
used by the FIQ handler for Amstrad Delta, this is required for successfull
compilation of arch/arm/plat-omap/fiq.c that provides several
usefull functions.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We cannot use the omap34xx_sram_init(). It needs to be implemented
for omap4. Otherwise we get an error and the system won't boot:
Unhandled fault: imprecise external abort (0x1406) at 0xea963e94
...
Fix this by adding a dummy omap44xx_sram_init().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Zoom2 and 3 have UARTs only on the external debug board.
GPMC needs to be mapped early to use it for DEBUG_LL.
Additionally, 0xfb000000 overlaps with other areas, so
use 0xfa400000 for the virtual address instead.
Note that with the pending serial.c patches you need to
set console=ttyS0,115200n8 as it will be the only UART
mapped. To use DEBUG_LL, you need to pass also earlyprintk
in cmdline.
Cc: Allen Pais <allen.pais@ti.com>
Acked-by: Vikram Pandita <vikram.pandita@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes the dependency to the UART1 being available for storing
the debug configuration in uncompress.h. This will simplify the
DEBUG_LL UART configuration for boards that may not have UART1, or
have an external UART as it requires only one mapping for DEBUG_LL.
The patch has a few limitations. Basically now we're assuming that
the kernel uncompress code won't overlap with OMAP_UART_INFO. We also
assume the printascii is called at least once before paging_init in
order for addruart to have a chance to read the UART setup from
OMAP_UART_INFO.
As suggested by Cyril Chemparathy <cyril@ti.com>,
Vikram Pandita <vikram.pandita@ti.com> and
Kevin Hilman <khilman@deeprootsystems.com>. Based on an earlier
patch posted for Davinci by Cyril Chemparathy <cyril@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we'll get an error about get_irqnr_and_base being defined
twice. Add an entry for omap4, and use ARCH_OMAP3 for omap3 instead of
ARCH_OMAP3430.
Also fix the check for omap1 to use ARCH_OMAP2PLUS to avoid having to
add ARCH_OMAP4 separately there.
Signed-off-by: Tony Lindgren <tony@atomide.com>
- registration with multi OMAP kernels support
- clocks
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
MUSB can supply upto 500mA such as, AM3517 and OMAP3EVM Rev >=E and thus
the 'power' field has to hold values above 255.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (39 commits)
omap: delete unused bootloader tag variables
omap: Devkit8000: Remove unused pins
omap: Devkit8000: Change position of init calls
omap: Devkit8000: Remove unnecessary include file
omap: Devkit8000: Fix typo in pin name
omap: Devkit8000: Add missing package selection
omap: Devkit8000: Fix typo in supplies
n8x0_defconfig: remove CONFIG_NILFS2_FS override
omap: board-sdp-flash.c: Fix typos in debug output
omap4: Fix McBSP4 base address
omap: rx51_defconfig: Remove CONFIG_SYSFS_DEPRECATED*=y options
omap: rx51_defconfig: Remove duplicate phonet
omap: fix a gpmc nand problem
AM3517: initialize i2c subsystem after mux subsystem
omap: remove one of the define of INT_34XX_BENCH_MPU_EMUL
omap: fix the compile error if CONFIG_MTD_NAND_OMAP2 is notenabled
OMAP4: Clocks: Change SPI Instance Names
omap: Devkit8000: Fix wrong usb port on Devkit8000
OMAP4: Fix for CONTROL register Base
OMAP4-HSMMC: FIX for MMC5 Controller IRQ Base
...
They are not needed and add over 512 bytes to kernel data.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
INT_34XX_BENCH_MPU_EMUL was defined twice, another is at Line 312.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_MTD_NAND_OMAP2 is not enabled, there will be a compile error,
"gpmc_nand_init() is not defined". Add a inline noop function to fix it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the base address of CONTROL register on OMAP4430SDP.
The control base is used by peripherals like MMC1 for PBIAS configuration.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The register DMA4_CDAC needs to be initialized to zero
before starting DMA transfer.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Govindraj R <govindraj.raja@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Reported-by:S, Venkatraman <svenkatr@ti.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since IRQ_TYPE_EDGE_BOTH is defined as (IRQ_TYPE_EDGE_FALLING |
IRQ_TYPE_EDGE_RISING), testing against it with a bitwise AND also matches
both single-edge cases in addition to the intended both edges case. Fix it,
replacing with a more accurate expression.
Created and tested againts linux-2.6.34-rc3.
Applicable to 2.6.33-stable as well.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the 32k sync timer is used for sched_clock(), it should count
time from the kernel boot (clocksource init) instead of the last HW
reset. Otherwise printk.time values will jump suddenly during the boot:
[ 0.000000] calling omap2_clk_arch_init+0x0/0x138 @ 1
[ 0.000000] initcall omap2_clk_arch_init+0x0/0x138 returned -22 after 0 usecs
[ 0.000000] initcall omap2_clk_arch_init+0x0/0x138 returned with error code -22
[ 0.000000] calling omap_init_clocksource_32k+0x0/0x98 @ 1
[ 508.697937] initcall omap_init_clocksource_32k+0x0/0x98 returned 0 after 0 usecs
[ 508.697967] calling omap_init_devices+0x0/0x38 @ 1
[ 508.698425] initcall omap_init_devices+0x0/0x38 returned 0 after 0 usecs
This will confuse tools such as scripts/bootgraph.pl.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch corrects the width of sysc_flags in hwmod sysconfig structure
where the values to be stored to this variable exceed the current
field width.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: edited to apply; rearranged structure members to pack]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The MsBSP register cache will never have any error/status flags set, since
these flags are never written to the reg_cache. So it is kind of not
necessary to clear these flags, which are actually always 0.
In other words, clearing the status/error flags are not necessary, since the
reg_cache will never got these bits set. We can just write back the
register content from the cache as it is when clearing an error condition.
Tested on Amstrad Delta.
Reported-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
New functions for querying the FIFO caused delay on both
TX and RX path.
On TX path the return value shows the number of used
locations in the FIFO.
On RX papth it returns the number of locations to be filled
to reach the threshold value (DMA will be triggered to read
the data out from the FIFO).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently if omap2420 is defined but not omap2430, cpu_is_omap2430()
is still defined as a macro, instead of #define'd to zero. This
results in conditional cpu_is_omap2430() code still being compiled,
and leads to possible compile/link errors. In particular for hwmod
init.
To fix, add extra #ifdefs to CPU check macros to ensure that the
is_omap* macros are zero for each OMAP2 if they are not configured
into the kernel.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For omap4 case, this was wrongly writing GPIO_LEVELDETECTx
registers with OMAP24XX_ offset and OMAP4_ offset.
Bug introduced in commit:
commit 3f1686a9bf
Author: Tony Lindgren <tony@atomide.com>
Date: Mon Feb 15 09:27:25 2010 -0800
omap: Fix gpio.c for multi-omap for omap4
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/plat-omap/include/plat/blizzard.h:9:
ERROR: spaces prohibited around that ':' (ctx:WxW)
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch follows the commit be093beb60
by Russell King:
OMAP wishes to pass state to the boot loader upon reboot in order
to instruct it whether to wait for USB-based reflashing or not.
There is already a facility to do this via the reboot() syscall,
except we ignore the string passed to machine_restart().
The patch adds the missing parameter to omap1_arch_reset() and
omap_prcm_arch_reset(), and modifies the latter to pass the reboot
command parameter to the boot loader instead of reboot mode (which is
for kernel internal use only and cannot be modified by the userspace).
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
the early_param() call in board-omap3touchbook.c expands to:
static const char __setup_str_early_touchbook_revision[]
__section(.init.rodata) _aligned(1) = tbr;
[...]
and we have a non-const variable being added to the
same section:
static struct ehci_hcd_omap_platform_data ehci_pdata
__section(.init.rodata);
because of that, gcc generates a section type conflict
which can (and actually should) be avoided by marking
const every variable marked with __initconst.
This patch fixes that for the ehci_hdc_omap_platform_data.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit b63128e812 broke the pin muxing
for I2C busses that are enabled from the kernel command line.
Fix this by defining the board registration function omap_register_i2c_bus
in common platform code as it was before but keep the muxing in architecture
dependent files.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 platform the iclk control is completly under hardware control
and no software control is available.
This difference w.r.t previous OMAP's needs all the common driver
accross OMAP's , cpu_is_xxxx() checks. To avoid poulluting the
drivers dummy clock nodes are created (The autogeneration
script has been updated accordingly).
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: made OMAP1 dummy_ck common and edited patch to reuse that]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add support for categorizing and iterating over hardware IP blocks by
the "class" of the IP block. The class is the type of the IP block:
e.g., "timer", "timer1ms", etc. Move the OCP_SYSCONFIG/SYSSTATUS data
from the struct omap_hwmod into the struct omap_hwmod_class, since
it's expected to stay consistent for each class. While here, fix some
comments.
The hwmod_class structures in this patch were designed and proposed by
Benoît Cousson <b-cousson@ti.com> and were refined in a discussion
between Thara Gopinath <thara@ti.com>, Kevin Hilman
<khilman@deeprootsystems.com>, and myself.
This patch uses WARN() lines that are longer than 80 characters, as
Kevin noted a broader lkml consensus to increase greppability by
keeping the messages all on one line.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add ARM_L1_CACHE_SHIFT_6 to arch/arm/Kconfig to allow CPUs with
L1 cache lines which are 64bytes to indicate this without having to
alter the arch/arm/mm/Kconfig entry each time.
Update the mm Kconfig so that ARM_L1_CACHE_SHIFT default value
uses this and change OMAP3 and S5PC1XX to select ARM_L1_CACHE_SHIFT_6.
Acked-by: Ben Dooks <ben-linux@fluff.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Code should be able to #include any header file without the fear that
the header file will go allocating memory. This is a coding style
issue, similar to commit 82e9bd5885.
Move the existing hwmod data from .h files to .c files.
While here, convert "omap34xx" to "omap3xxx" in the hwmod files, since
most of these structures should be reusable across all OMAP3 chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The OMAP hwmod core code is intended to use SoC IP block description
structures that are autogenerated from TI's OMAP hardware database.
Currently the hwmod code uses clkdev device + connection addressing to
identify clocks. This causes problems in the hwmod autogeneration
process, since the TI hardware database doesn't use platform_device or
clkdev addressing; it uses a single clock signal name string, which
tends to bear some resemblance to what is used in the OMAP TRMs. This
patch converts the hwmod code and existing data to use omap_clk_get_by_name(),
introduced in the previous patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
The OMAP hwmod core code is intended to use SoC IP block description
structures that are autogenerated from TI's OMAP hardware database.
Currently the hwmod code uses clkdev device + connection addressing to
identify clocks. This causes problems in the hwmod autogeneration
process, since the TI hardware database doesn't use platform_device or
clkdev addressing; it uses a single clock signal name string, which
tends to bear some resemblance to what is used in the OMAP TRMs. This
patch adds a non-exported function to the OMAP clock code,
omap_clk_get_by_name(). A subsequent patch will convert the hwmod
code to use this function.
This function is for use only by core code, and practically, no other
code outside the hwmod code should need it. Device driver code in the
kernel must not use this function, which is why it is not exported.
Drivers should use the appropriate clock alias provided by the clkdev
data structures, so driver code can be completely SoC-independent.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Get rid of the ALWAYS_ENABLED clock flag - it doesn't actually do anything.
(The OMAP4 clock autogeneration scripts have been updated accordingly.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
The RATE_FIXED clock flag is pointless. In the OMAP1 clock code, it
simply causes the omap1_clk_round_rate() function to return the
current rate of the clock. omap1_clk_round_rate(), however, should
never be called for a fixed-rate clock, since none of these clocks
have a .round_rate function pointer set in their struct clk records.
Similarly, in the OMAP2+ clock code, the RATE_FIXED flag just causes
the clock code to emit a warning if the OMAP clock maintainer was
foolish enough to add a .round_rate function pointer to a fixed-rate
clock. "Doctor, it hurts when I pretend that a fixed-rate clock is
rate-changeable." "Then don't pretend that a fixed-rate clock is
rate-changeable." It has no functional value. This patch drops the
RATE_FIXED clock flag, removing it from all clocks that are so marked.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
All of the clocks that are marked with DELAYED_APP are changed as part
of the virt_prcm_set OPP virtual clock. On 24xx, these clocks all
need to be changed as part of a group to keep the clock tree
functional - hence the need for the VALID_CONFIG bit, which is not
present on later OMAPs. These clocks should not be rate-changed
independently. So prevent these clocks from being changed
independently by dropping their .round_rate and .set_rate function
pointers. It then turns out that the DELAYED_APP clock flag is no
longer useful, so drop it and the associated code and renumber the
clock flags.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
After the clkdev conversion, the struct clk.id field became
superfluous, so, drop it. Bring the clock names closer to the TRMs
and ensure they are unique for debugfs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There are now only eight OMAP clock flags, so renumber the flags to
fit in a u8 and shrink the size of struct clk.flags from a u32 to a
u8. The intention is to save memory.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
It turns out that the only purpose of the CONFIG_PARTICIPANT clock
flag is to prevent omap2_clk_set_rate() and omap2_clk_set_parent()
from being executed on clocks with that flag set. The rate-changing
component can be more directly accomplished by dropping the .set_rate
and .round_rate function pointers from those CONFIG_PARTICIPANT struct
clks. As far as the parent-changing component is concerned, it turns
out that none of the CONFIG_PARTICIPANT clocks have multiple parent
choices, so all that is necessary is for omap2_clk_set_parent() to
bail out early if the new parent is equal to the old parent.
Implement this change and get rid of the flag, which has always had a
confusing name (it appears to be a Kconfig option, falsely).
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
The CLOCK_IN_OMAP4430 clock flag is not currently needed in the OMAP4
ES1 clock tree, and platform discrimination via clock flags is
deprecated in favor of the clkdev mechanism, so, drop it. (The OMAP4
clock tree autogeneration script has been updated accordingly.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The maximum DPLL multiplier (M) values for OMAP2xxx and OMAP3xxx are
one increment higher than they should be. See for example the
OMAP242x TRM Rev X Section 5.10.6 "Clock Generator Registers" and the
OMAP36xx TRM Rev C Table 3-202 "CM_CLKSEL1_PLL". Programming a 0 into
the DPLL's M register bitfield is valid for OMAP2/3 and indicates that
the DPLL should enter MN-bypass mode. Also, increase the minimum
multiplier (M) value for the DPLL rate rounding code from 1 to 2, to
ensure that it does not inadvertently put the DPLL into bypass.
Note that the register documentation in the OMAP2xxx and OMAP3xxx TRMs
does not make clear that the actual DPLL divider value (the "N") is
the content of the appropriate register bitfield for the N value,
_plus one_. (In other words, an N register bitfield of 0 indicates a
DPLL divider value of 1.) This is only clearly documented in the
OMAP4430 TRM, in, for example, OMAP4430 TRM Rev A Table 3-1167
"CM_CLKSEL_DPLL_USB".
While here, update copyrights, add kerneldoc for struct dpll_data,
drop the unused struct dpll_data.max_tolerance field, remove some
unnecessary #includes in DPLL-related code, and replace the #include
of <linux/module.h> with <linux/list.h>, which is what was really
needed. The OMAP4 clock autogenerator script has been updated
accordingly.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
In 3630, DPLL4M2 output can be 96MHz or 192MHz (for SGX to run at
192). This patch has changes to support this feature. 96MHz clock is
generated by dividing 192Mhz clock by 2 using CM_CLKSEL_CORE register.
SGX can select Core Clock, 192MHz clock or CM_96M_FCLK as it's
functional clock. In summary changes done are:
1. Added a feature called omap3_has_192mhz_clk and enabled for 3630
2. Added a new clock node called omap_192m_alwon_ck
3. Made omap_96m_alwon_fck to derive its clock from omap_192m_alwon_ck
Signed-off-by: Vishwanath BS <Vishwanath.bs@ti.com>
[paul@pwsan.com: fixed whitespace]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Divider (M2, M3, M4, M5 and M6) field width has been increased by 1 bit
in 3630. This patch has changes to accommodate this in CM dynamically
based on chip version.
Basically new clock nodes have been added for 3630 DPLL4 M2,M3,M4,M5 and
M6 and value of these nodes are used if cpu type is 3630.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[paul@pwsan.com: updated to apply on 2.6.34 queue; comments added]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
DPLL4 for 3630 introduces a changed block called j type dpll, requiring
special divisor bits and additional reg fields. To allow for silicons to
use this, this is introduced as a flag and is enabled for 3630 silicon.
OMAP4 also has j type dpll for usb.
Tested with 3630 ZOOM3 and OMAP3430 ZOOM2
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <Vishwanath.bs@ti.com>
[paul@pwsan.com: added some comments; updated copyrights and credits; fixed
some style issues]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds support in omap device layer to register devices
as early platform devices. Certain devices needed during system boot up
like timers, gpio etc can be registered as early devices. This will
allow for them to be probed very early on during system boot up.
This patch adds a parameter is_early_device in omap_device_build.
Depending on this parameter a call to early_platform_add_devices
or platform_register_device is made.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP3 Some modules like Smartreflex do not have the regular sysconfig
register.Instead clockactivity bits are part of another register at a
different bit position than the usual bit positions 8 and 9.
In OMAP4, a new scheme is available due to the new protocol
between the PRCM and the IPs. Depending of the scheme, the SYSCONFIG
bitfields position will be different.
The IP_REVISION register should be at offset 0x00.
It should contain a SCHEME field. From this we can determine whether
the IP follows legacy scheme or the new scheme.
31:30 SCHEME Used to distinguish between old scheme and current.
Read 0x0: Legacy protocol.
Read 0x1: New PRCM protocol defined for new OMAP4 IPs
For legacy IP
13:12 MIDLEMODE
11:8 CLOCKACTIVITY
6 EMUSOFT
5 EMUFREE
4:3 SIDLEMODE
2 ENAWAKEUP
1 SOFTRESET
0 AUTOIDLE
For new OMAP4 IP's, the bit position in SYSCONFIG is (for simple target):
5:4 STANDBYMODE (Ex MIDLEMODE)
3:2 IDLEMODE (Ex SIDLEMODE)
1 FREEEMU (Ex EMUFREE)
0 SOFTRESET
Unfortunately In OMAP4 also some IPs will not follow any of these
two schemes. This is the case at least for McASP, SmartReflex
and some security IPs.
This patch introduces a new field sysc_fields in omap_hwmod_sysconfig which
can be used by the hwmod structures to specify the offsets for the
sysconfig register of the IP.Also two static structures
omap_hwmod_sysc_type1 and omap_hwmod_sysc_type2 are defined
which can be used directly to populate the sysc_fields if the IP follows
legacy or new OMAP4 scheme. If the IP follows none of these two schemes
a new omap_hwmod_sysc_fields structure has to be defined and
passed as part of omap_hwmod_sysconfig.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Current implementation defines clock idle state indicators based on the
cpu information (cpu_is_omap24xx() or cpu_is_omap34xx()) in a system wide
manner. This patch extends the find_idlest() function in clkops to pass
back the idle state indicator for that clock, thus allowing idle state
indicators to be defined on a per clock basis if required.
This is specifically needed on AM35xx devices as the new IPSS clocks
indicates the idle status (0 is idle, 1 is ready) in a way just
opposite to how its handled in OMAP3 (0 is ready, 1 is idle).
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
[paul@pwsan.com: updated to apply after commit 98c45457 et seq.]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds counters to keep track of whether the powerdomain
logic or software controllable memory banks are turned off when
the power domain enters retention. During power domain retention
if logic gets turned off, the scenario is known as Open Switch Retention.
Also during retention s/w controllable memory banks of a power
domain can be chosen to be kept in retention or off.
This patch adds one counter per powerdomain to track the power domain
logic state during retention. Number of memory bank state counters
added depends on the number of software controllable memory banks
of the powerdomain. To view these counters do
cat ../debug/pm_debug/count
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: conditional expressions simplified; counter increment
code moved to its own function]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds APIs pwrdm_read_logic_retst and
pwrdm_read_mem_retst for reading the next programmed
logic and memory state a powerdomain is to hit in event
of the next power domain state being retention.
These are needed for OSWR support.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_device_[enable|idle|shutdown] functions print a warning
when called from an invalid state. Print the invalid state in
the warning messages. This also uses __func__ to get the function
name.
Also, move the entire print string onto a single line to facilitate
grepping or error messages. Recent discussions on LKML show
strong preference for grep-able code vs. strict 80 column limit.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_device struct contains a 'struct platform_device'. Normally,
converting a platform_device pointer to an omap_device pointer
consists of simply doing a container_of(), as is done currently by the
to_omap_device() macro.
However, if this is attempted when using platform_device that has not
been created as part of the omap_device creation, the container_of()
will point to a memory location before the platform_device pointer
which will contain random data.
Therefore, we need a way to detect valid omap_device pointers. This
patch solves this by using the simple magic number approach.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Move check/set/get_timings() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move set/get_wss() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move enable/disable/suspend/resume from omap_dss_device to
omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move update() and sync() from omap_dss_device to omap_dss_driver.
Also, update was hardcoded to use virtual channel 0. This patch adds a
parameter that specifies the VC.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move set/get_update_mode() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move enable/get_te() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move get_recommended_bpp() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move get_resolution() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move enable/disable_channel() from omap_dss_device to overlay manager.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move wait_vsync() from omap_dss_device to overlay manager.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move get/set_rotate() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move set/get_mirror() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move memory_read() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Move run_test() from omap_dss_device to omap_dss_driver.
This is part of a larger patch-set, which moves the control from omapdss
driver to the display driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
keventd_wq is a shared work-queue, and should not be used when we
need fast deterministic response. Instead mailbox driver should
use it's own private work-queue, with it's own thread, to ensure
that handling of RX interrupts are not delayed by other drivers.
The tasklet is still used for transmission of mbox messages.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: C A Subramaniam <subramaniam.ca@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes all the omap4 specific irq line
defines from plat/irqs.h and includes auto-generated
irqs-44xx.h
All the legacy naming style defines are replaced with the one
from irqs-44xx.h
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated to compile with usb-musb.c]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes all the omap4 specific dma request
lines defines from plat/dma.h and includes dma-44xx.h
The defines are aligned so no driver should be impacted
because of this change.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These files are generated along with the HWMOD and will eventually be
in the existing header files as soon as all drivers will be migrate to
omap_hwmod / omap_device.
The dma-44xx.h and irqs-44xx.h file should be in
'arch/arm/mach-omap2/include/mach/', but omap1 and omap2plus common devices
still share these defines and hence currently placed in plat-omap/include/plat/
directory.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a save and restore mechanism for ARM L2 auxiliary control
register. The feature is enabled by default for GP devices, but for HS/EMU
devices the user must enable the service and define the PPA service ID to
be used for setting L2 aux ctrl, as this is not currently supported by the
bootloader. If nobody alters the contents of L2 aux ctrl from its reset
value, this feature is not needed.
Kconfig option to enable HS/EMU L2 aux save and restore:
- OMAP3_L2_AUX_SECURE_SAVE_RESTORE
Kconfig option to select HS/EMU PPA service for setting L2 aux ctrl:
- OMAP3_L2_AUX_SECURE_SERVICE_SET_ID
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes the L4 wakeup io mapping section for omap3
and omap4. L4 wakeup space is part of 4MB L4 space which is
already mapped and hence remove the overlapped mapping.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the omap_type function to detect whether the device
is GP or HS
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 'ba50ea7e' reserves DMA channels 0 and 1 on high
security devices, in order to avoid collision between kernel
dma transfers and ROM code dma transfers.
This fix is applicable only for OMAP3 so add an appropriate
check.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
CC: Kalle Jokiniemi <kalle.jokiniemi@digia.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch enables smart-idle idlemodes and autoidle for sDMA
on OMAP4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is a clean-up patch towards dynamic allocation of IO space
instead of using harcoded macros to calculate virtual addresses.
Also update the sdrc, prcm and control module to allocate
iospace dynamically
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add sidetone feature to McBSP instances 2 and 3 on OMAP3 based devices.
Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for Mentor USB to 4430 SDP board
file.
It also defines the base address for HS USB OTG controller
in OMAP4.
Also updates platform specfic structure with base address
and IRQ details.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.
Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The system to allow panel drivers to exists as attached to ctrl drivers
did never work very well. It is not useed, and this patch removes it to
make the driver cleaner.
For now, controller drivers need to include also the panel driver code. In
the future a proper mechanism for this should be developed, perhaps by
creating busses for controllers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
This patch adds L2 Cache support for OMAP4. External L2 cache
is used in OMAP4
CC: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows the procfs vmallocinfo file to show who created the ioremap
regions. Note: __builtin_return_address(0) doesn't do what's expected
if its used in an inline function, so we leave __arm_ioremap callers
in such places alone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add platform device for McPDM interface in OMAP4 and register
its memory and irq resources.
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define McPDM physical and L3 base address for OMAP4
Signed-off-by: Jorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3517/05 has few additional control module registers to control
the new IP's, like VPFE, USBOTG, CPGMAC.
This patch adds the bit defination for INTR_CLR and SW_RST control
register.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.
If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers. However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.
This patch adds a platform data field to allow
that option.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode. Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves the setup code for GPIO's and Voltage
Regulators from the board file mmc-twl4030.c to the
driver omap_hsmmc.c. PBIAS and other system control
configuration remains in the board file.
Moving GPIO code to the driver makes the board initialisation
code independent of when GPIO's are defined. That makes the
board initialisation now entirely independent of its original
twl4030 roots.
Moving Voltage Regulator code to the driver allows for further
development of regulator support in the core MMC code. It also
permits the MMC core to be compiled as a module, because the
board code no longer calls MMC core functions.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds 'board-sdp-flash.c', which could be utilized
by boards similar to 3430SDP. (For ex: 2430sdp, 36030sdp).
This file does initialization for all three flash devices present
in SDP boards (NOR, NAND, OneNAND), by finding there 'cs' number
dynamically using switch setting information (S8: 1-4).
This also expects partition information from core board files (for
ex: board-3430sdp.c). Which allows to choose different default
partitions for different boards.
A new structure is created for this purpose: 'flash_partitions'
in 'mach/board-sdp.h'. This has two members:
1. struct mtd_partition *parts
2. int nr_parts
A board file is expected to fill this structure and pass it to
'sdp-flsash-init'. Partition information should be passed in
structure array of 'flash_partitions'. Partition information should
be passed in below sequence in array:
NOR
OneNAND
NAND
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introducing 'gpmc-nand.c' for GPMC specific NAND init.
For example: GPMC timing parameters and all.
This patch also migrates gpmc related calls from 'nand/omap2.c'
to 'gpmc-nand.c'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the way McBSP registers are updated: use cached values instead of
relying upon those read back from the device.
With this patch, I have finally managed to get rid of all random
playback/recording hangups on my OMAP1510 based Amstrad Delta hardware. Before
that, values read back from McBSP registers to be used for updating them
happened to be errornous.
From the hardware side, the issue appeared to be caused by a relatively high
power requirements of an external USB adapter connected to the board's printer
dedicated USB port.
I think there is one important point that makes this patch worth of applying,
apart from my hardware quality. With the current code, if it ever happens to
any machine, no matter if OMAP1510 or newer, to read incorrect value from a
McBSP register, this wrong value will get written back without any checking.
That can lead to hardware damage if, for example, an input pin is turned into
output as a result.
Applies on top of patch 3 from this series:
[PATCH v9 3/4] OMAP: McBSP: Introduce caching in register write operations
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with omap_3430sdp_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine cache size required per McBSP port at init time, based on
processor type running on.
Allocate space for storing cached copies of McBSP register values at
port request.
Modify omap_msbcp_write() function to update the cache with every
register write operation.
Modify omap_mcbsp_read() to support reading from cache or hardware.
Update MCBSP_READ() macro for modified omap_mcbsp_read() function API.
Introduce a new macro that reads from the cache.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with: omap_perseus2_730_defconfig, omap_generic_1610_defconfig,
omap_generic_2420_defconfig, omap_2430sdp_defconfig, omap_3430sdp_defconfig,
omap_4430sdp_defconfig with CONFIG_OMAP_MCBSP=y selected.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_MCBSP_READ()/_WRITE() macros and omap_mcbsp_read()/_write() functions
accept McBSP register base address as an argument. In order to support
caching, that must be replaced with an address of the omap_mcbsp structure
that would provide addresses for both register AND cache access.
Since OMAP_ prefix seems obvious in macro names, drop it off in order to
minimize line wrapping throughout the file.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with omap_3430sdp_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are several places where readw()/writew() functions are used instead of
OMAP_MCBSP_READ()/WRITE() macros for manipulating McBSP registers. Replace
them with macros to ensure consistent behaviour after caching is introduced.
Tested on OMAP1510 based Amstrad Delta.
Compile-tested with omap_3430sdp_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There was a potential risk that the following "memset" could override
its range if a given address was not the 1st entry of a
largepage. This is not the case for "iovmm".
Reported-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There was a potential risk that the following "memset" could override
its range if a given address was not the 1st entry of a
supersection. This is not the case for "iovmm".
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is just a cleanup, but adds a few macros here, which can be used
in the proceeding patches.
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OMAP based boards to use physmap-flash. Refreshed against today's
Linux omap kernel tree
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Set up METHOD_GPIO_44XX instead of trying to use the METHOD_GPIO_24XX.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we can include it easily as needed also for .S files.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix dmtimer.c for multi-omap boot. Also remove legacy
clk_enable/disable wrappers that are no longer needed.
Note that the clock handling should be further improved
to make use of the clock aliases.
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are no longer needed. Note that zoom boards
should now set their own function in uncompress.h
and debug-macro.S for the external UART.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename and export dsi_vc_enable_hs() so that the display drivers can
control the mode of the DSI link.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
I have found an access to already released memory in
clk_debugfs_register_one() function.
Signed-off-by: Marek Skuczynski <mareksk7@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only usage of _toggle_gpio_edge_triggering is in
an #ifdef CONFIG_ARCH_OMAP1 block, so only provide it if
CONFIG_ARCH_OMAP1 is defined, too.
This fixes a compiler warning:
arch/arm/plat-omap/gpio.c:758: warning: '_toggle_gpio_edge_triggering' defined but not used
when compiling for ARCH_OMAP2, ARCH_OMAP3 or ARCH_OMAP4.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some HW blocks have errata which requires specific slave idle mode
under certain conditions.
This patch adds an hwmod API to allow setting slave idlemode
ensuring that any SYSCONFIG register updates go through hwmod.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
First, this patch adds new worst-case latency values to the
omap_device_pm_latency struct. Here the worst-case measured latencies
for the activate and deactivate hooks are stored.
In addition, add an option to auto-adjust the latency values used for
device activate/deactivate.
By setting a new 'OMAP_DEVICE_LATENCY_AUTO_ADJUST' flag in the
omap_device_pm_latency struct, the omap_device layer automatically
adjusts the activate/deactivate latencies to the worst-case measured
values.
Anytime a new worst-case value is found, it is printed to the console.
Here is an example log during boot using UART2 s an example. After
boot, the OPP is manually changed to the 125MHz OPP:
[...]
Freeing init memory: 128K
omap_device: serial8250.2: new worst case deactivate latency 0: 30517
omap_device: serial8250.2: new worst case activate latency 0: 30517
omap_device: serial8250.2: new worst case activate latency 0: 218139648
omap_device: serial8250.2: new worst case deactivate latency 0: 61035
omap_device: serial8250.2: new worst case activate latency 0: 278076171
omap_device: serial8250.2: new worst case activate latency 0: 298614501
omap_device: serial8250.2: new worst case activate latency 0: 327331542
/ # echo 125000 > /sys/devices/system/cpu/cpu0/cpufreq/scaling_setspeed
omap_device: serial8250.2: new worst case deactivate latency 0: 91552
Motivation: this can be used as a technique to automatically determine
the worst case latency values. The current method of printing a
warning on every violation is too noisy to actually interact the
console in order to set low OPP to discover latencies.
Another motivation for this patch is that the activate/deactivate
latenices can vary depending on the idlemode of the device. While
working on the UARTs, I noticed that when using no-idle, the activate
latencies were as high as several hundred msecs as shown above. When
the UARTs are in smart-idle, the max latency is well under 100 usecs.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch only affects documentation; no functional changes are
included.
Clean up comments in the current clockdomain, powerdomain code and
header files. This mostly involves conversion to kerneldoc format,
although some clarifications are also included.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch rearranges the order of structure members in struct powerdomain
to avoid wasting memory due to alignment restrictions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add usecounting for wakeup and sleep dependencies. In the current
situation, if several functions add dependencies on the same
clockdomains, when the first dependency removal function is called,
the dependency will be incorrectly removed from the hardware.
Add clkdm_clear_all_wkdeps() and clkdm_clear_all_sleepdeps(), which
provide a fast and usecounting-consistent way to clear all hardware
clockdomain dependencies, since accesses to these registers can be
quite slow. pm{2,3}4xx.c has been updated to use these new functions.
The original version of this patch did not touch these files, which
previously wrote directly to the wkdep registers, and thus confused
the usecounting code. This problem was found by Kevin Hilman
<khilman@deeprootsystems.com>.
N.B.: This patch introduces one significant functional difference over
the previous pm34xx.c code: sleepdeps are now cleared during
clockdomain initialization, whereas previously they were left
untouched. This has been tested by Kevin and confirmed to work.
The original version of this patch also did not take into
consideration that some clockdomains do not have sleep or wakeup
dependency sources, which caused NULL pointer dereferences. This
problem was debugged and fixed by Kevin Hilman
<khilman@deeprootsystems.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Jouni Högander <jouni.hogander@nokia.com>
OMAP clockdomains and powerdomains are currently defined statically,
only registered at boot, and never unregistered, so we can remove the
unregister function and the locking. A variant of this was originally
suggested a while ago by Dmitry Baryshkov <dbaryshkov@gmail.com>.
This version of this patch contains an additional fix from Kevin Hilman
<khilman@deeprootsystems.com> to address one of the pwrdm_for_each_nolock()
users in mach-omap2/pm-debug.c. Thanks Kevin.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Move clockdomain wakeup dependency and sleep dependency data
structures from the powerdomain layer to the clockdomain layer, where
they belong. These dependencies were originally placed in the
powerdomain layer due to unclear documentation; however, it is clear
now that these dependencies are between clockdomains. For OMAP2/3,
this is not such a big problem, but for OMAP4 this needs to be fixed.
Thanks to Benoît Cousson <b-cousson@ti.com> for his advice on this
patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
One of the OMAP1 clocks can use the fixed divisor recalculation code
introduced in the OMAP2 clock code, so rename the
omap2_fixed_divisor_recalc() function to omap_fixed_divisor_recalc()
and make it available to all OMAPs. A followup patch converts the OMAP1
clock.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add CK_* flags for the two new Sitara chips, AM3505 and AM3517, and
the OMAP34xx die shrink, OMAP36xx/OMAP37xx. Introduce a new CK_*
flag, CK_3XXX, that marks all clocks that are common to OMAP3 family
chips. CK_343X now refers to clocks that are available only on
OMAP34{1,2,3,4}0 (WTBU) and OMAP35{03,15,25,30} (any version).
At some point, the RATE_IN_* flags should be updated also.
While here, add some documentation describing the chip families
covered by these clock flags.
This patch is partially based on patches from Ranjith Lohithakshan
<ranjithl@ti.com> and Vishwanath Sripathy <vishwanath.bs@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Ranjith Lohithakshan <ranjithl@ti.com>
Cc: Vishwanath Sripathy <vishwanath.bs@ti.com>
AM3517/05 has a few additional control module registers defined mainly
to control the new IP's. This patch adds support for those new registers.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Here the ".clkstctrl_reg" field is added to the clockdomain stucture
as the module offsets for OMAP4 do not map one to one for powerdomains
and clockdomains as it used to for OMAP3. Hence we need to use absolute
addresses to access the control registers. Some of the clock domains have
modules falling in the address space of PRM partition. Hence necessitating
the use of absolute adresses.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Taking care of the platform specific and common power domains with
proper checks. Also refining some Macros according to the latest
OMAP4 requirements.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The Autogenerated OMAP4 power domain specific file (mach-omap2/powerdomains44xx.h)
is added here.
This file is auto-generated using python scripting and following is the list of the people
involved:
Paul Walmsley
Benoit Cousson
Abhijit Pagare
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Some of the OMAP4 specific chip level initialisations are taken care of.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
[paul@pwsan.com: updated to use '4430ES1' rather than simply '4430'; updated
to apply after the intervening cpu.h/id.c patch; thanks also to Tony
for catching a bug in my rewrite]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP GP timers keep running for a few cycles after they are stopped,
which can cause the timer to expire and generate an interrupt. The
pending interrupt will prevent e.g. OMAP from entering suspend, thus
we ack it manually. Only applicable on OMAP2/3/4.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
During suspend, the kernel timekeeping subsystem is shut down. Before
suspend and upon resume, it uses a weak function
read_persistent_clock() to determine the amount of time that elapsed
during suspend.
This function was not implemented on OMAP, so from the timekeeping
subsystem perspective (and thus userspace as well) it appeared that no
time elapsed during suspend.
This patch uses the 32k sync timer as a the persistent clock.
NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so
more than one wrapping of the 32k sync timer during suspend may
cause problems. Also note there are not interrupts when the 32k
sync timer wraps, so something else has to be done.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
We need to set the omap_chip.oc carefully for the clocks to work.
To fix this, set the omap_chip.oc in omap3_check_features() based
on the CONTROL_IDCODE and silicon revision registers.
Also add handling for 34xx es3.1.2 as es3.1 for now.
Fixes booting on at least overo board.
Based on an earlier patch by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In the current implementation the sysconfig value is read into
_sysc_cache once and an actual update to the sysconfig register
happens only if the new value paased is differnt from the one in _sysc_cache.
_sysc_cache is updated only if _HWMOD_SYSCONFIG_LOADED is not set.
This can lead to the follwing issue if off mode is enabled in modules
which employs "always-retore" mechanism of context save and restore.
a. The module sets the sysconfig register through omap_device_enable.
Here _sysc_cache is updated with the value written to the sysconfig
register and left.
b. The power domain containig the module enters off mode and the
module context is lost.
c. The module in use becomes active and calls omap_device_enable to
enable itself. Here a read of sysconfig register does not happen
as _HWMOD_SYSCONFIG_LOADED flag is set. The value to be written
to the sysconfig register will be same as the one written in step a.
Since _sysc_cache reflects the previous written value an update
of the sysconfig register does not happen.
This means in modules which employs "always-restore" mechanism
after off , the sysconfig regsiters will never get updated.
This patch introduces a flag SYSC_NO_CACHE which if set ensures that the
sysconfig register is always read into _sysc_cache before an update is
attempted.
This flags need to be set only by modules which does not do a context save
but re-initializes the registers every time the module is accessed. This
includes modules like i2c, smartreflex etc.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: tweaked to apply on a different head, added flag comment]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
A subsequent patch adds code on OMAP2xxx to dynamically allocate the
CPUFreq frequency table in clk_init_cpufreq_table(), so for it to
avoid a leak, it will need a corresponding function to free the
memory. This patch adds clk_exit_cpufreq_table() with generic
code to call a chip-specific variant inside the clockfw_lock spinlock via
struct clk_functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The only symbols that should be exported are symbols that are to be
called from loadable kernel modules, e.g., device drivers. In the
context of plat-omap/clock.c, these should only be the Linux clock
interface symbols as defined by include/linux/clk.h. Core code
doesn't need these symbols to be exported. Also, clean up an old
comment while here.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 10db25fea4 causes the following
kernel messages during N800 boot (and presumably all other 2420
boards):
[ 0.000000] BUG: mapping for 0x58000000 at 0xe0000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x59000000 at 0xe1000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x5a000000 at 0xe2000000 overlaps vmalloc space
Fix by remapping the IVA memory areas somewhere outside vmalloc space.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Out of the three major OMAP2 chip types, OMAP2420, OMAP2430, and OMAP3430,
we only map the IVA on OMAP2420. The memory mapping is not shared between
OMAP2420 and OMAP2430, so it is inappropriate to label those macros as
'24XX'; this patch changes them to '2420'.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 9905a43b made struct backlight_ops const. Omap was
setting check_fb dynamically, which caused the following
compile error:
drivers/video/backlight/omap1_bl.c: In function 'omapbl_probe':
drivers/video/backlight/omap1_bl.c:142: error: assignment of read-only variable 'omapbl_ops'
Turns out pdata->check_fb is not being used, so just remove
it to fix the compile.
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Richard Purdie <rpurdie@linux.intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 35c9049b27 added
drivers/spi/omap_spi_100k.c.
This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some chips, namely any OMAP1 chips using METHOD_MPUIO,
OMAP15xx and OMAP7xx, cannot be setup to respond to on-chip GPIO
interrupts in both rising and falling edge directions -- they can
only respond to one direction or the other, depending on how the
ICR is configured.
Additionally, current code forces rising edge detection if both
flags are specified:
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
l &= ~(1 << gpio);
else
goto bad;
This change implements a toggle function that will modify the ICR
to flip the direction of interrupt for IRQs that are requested with
both rising and falling flags. The toggle function is not called
for chips and GPIOs it does not apply to through the use of a flip_mask
that's added on a per-bank basis. The mask is only set for those
GPIOs where a toggle is necessary. Edge detection starts out the
same as above with FALLING mode first.
The toggle happens on EACH interrupt; without it, we have the
following sequence of actions on GPIO transition:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt
0x1 1 -> 0 (falling) No interrupt
(set ICR to 0x0 manually)
0x0 0 -> 1 (rising) No interrupt
0x0 1 -> 0 (falling) Interrupt
That is, with the ICR set to 1 for a gpio, only rising edge interrupts
are caught, and with it set to 0, only falling edge interrupts are
caught. If we add in the toggle, we get this:
ICR GPIO Result
0x1 0 -> 1 (rising) Interrupt (ICR set to 0x0)
0x0 1 -> 0 (falling) Interrupt (ICR set to 0x1)
0x1 0 -> 1 ...
so, both rising and falling are caught, per the request for both
(IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING).
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In its current form, the omap_mcbsp_request() function can return after
irq_request() failure without any cleanups, effectively locking out the port
forever with clocks left running. Fix it.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for phoenix interrupt framework. New iInterrupt
status register A, B, C are introduced in Phoenix and are cleared on write.
Due to the differences in interrupt handling with respect to TWL4030,
twl6030-irq.c is created for TWL6030 PMIC
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In original implementation, the revision passed to
these macros contained revision number in lower nibble.
But, later the revision bits (OMAP_REVBITS_XX) were
defined to use omap_revision[15:08] where revision
number is containied in higher nibble.
This patch updates the macros; else incorrect revision
is detected for OMAP35xx devices.
Signed-off-by: Sanjeev Premi <premi@ti.com>
The runtime detection of OMAP3515 and OMAP3525
was reversed.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove unused data type omap_gpio_switch_config
Thereby also get rid of following sparse warnings:
arch/arm/plat-omap/include/plat/board.h :121:20:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :122:19:
warning: dubious bitfield without explicit `signed' or `unsigned'
arch/arm/plat-omap/include/plat/board.h :123:24:
warning: dubious bitfield without explicit `signed' or `unsigned'
Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Comment in omap_init_devices asks to keep init calls and their
implementations in alphabetical order, so let it be that way.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For NAND devices '2' should be used with GPMC_CONFIG1_DEVICETYPE
instead of '1'.
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds new function: omap_serial_init_port(port) that can be
used to initialize only selected UARTs as serial ports. Platforms can
then in their board files call this function instead of omap_serial_init()
if they don't want to use all UARTs as serial ports.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AuxCoreBoot0 and AuxCoreBoot1 can be only accessed in secure
mode. Replace the current code with secure monitor API's to access/modify
these registers.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the public sram base address and available
size on OMAP4430.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the OMAP4430 cpu detection. The IC rev detection is
done with hawkeye and rev. Note that rev does not map directly to
defined processor revision numbers as ES1.0 uses value 0.It also fixes
the SCM base address to read the correct ID_CODE register.
Also the cpu_is_omap44xx() and cpu_is_omap443x() correctly populated
instead of always being true
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initially only for 34xx. This code allows us to:
- Make the code more generic as the omap internal signal
names can stay the same across omap generations for some
devices
- Map mux registers to GPIO registers that is needed for
dynamic muxing of pins during off-idle
- Override bootloader mux values via kernel cmdline using
omap_mux=some.signa1=0x1234,some.signal2=0x1234
- View and set the mux registers via debugfs if
CONFIG_DEBUG_FS is enabled
Cc: Mike Rapoport <mike@compulab.co.il>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds dummy hooks for OMAP4 dpll api's. Removes
dummy hooks for clkdev api's and enables CLKDEV
for OMAP4.
Also comments clockdomain calls from within the clock
framework as its not supported yet for OMAP4.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch defines all the clock nodes in OMAP4430
platform. All the clock node structs and the clkdev table is
autogenerated using a python script (gen_clock_tree.py)
developed by Paul Walmsley, Benoit Cousson and Rajendra Nayak.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
This patch fixes the PRM and CM base addresses and adds
a new CM2 base address for OMAP4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Rather than having to do a usecs = nsecs / NSECS_PER_USEC to
track latency in usecs, just track it in nanoseconds.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
