Use %pM instead, and also remove stray variables
declared with DECLARE_MAC_BUF.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware V4 on CF8381 reports region code shifted by 1 byte to left.
The following patch checks for this and handles it properly.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SDIO driver sets the surpriseremoved flag before calling
lbs_remove_card. With IEEE PS enabled, lbs_remove_card must issue a
command to exit IEEE PS mode, however with that flag set the command
path is blocked and the card is never taken out of IEEE PS mode. This
step is required to ensure that the driver can be reloaded. This patch
moves the setting of surpriseremoved after lbs_remove_card is called.
Tested with V9 firmware by ensuring that IEEE PS is disabled when the
driver is removed. Reloading the driver is not fully tested due to a
separate issue with module reload in the SDIO driver, however this
patch at least leaves the card in a better state when we bring the
driver down.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SPI driver does a couple of card cleanup steps in the wrong order on
module removal. If IEEE PS is enabled, this results in the card being
left in IEEE PS mode and subsequent failures to reload the module. The
problem is that the surpriseremoved flag is set before calling
lbs_remove_card, but that function needs to issue a command to exit IEEE
PS mode (the flag blocks the command path). In addition, lbs_stop_card
should be called first because it clears out any pending commands.
Tested on a GSPI device with V9 firmware by confirming that we can
reload the module with or without IEEE PS enabled.
Also fix a warning from the wrong uint format in a printk.
V2: use z modifier, thanks Sebastian.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Libertas currently maintains a copy of the WPA unicast and group keys
when using WPA or WPA2. This copy is checked when deciding whether or
not to return to sleep in IEEE PS mode but the actual copying back to
priv was omitted, which breaks IEEE PS mode with WPA/WPA2 when one
issues commands that require temporarily keeping the device awake.
This patch introduces the omitted copy-back of the keys so that IEEE PS
functions correctly in WPA/WPA2 mode. Thanks to Dan Williams for
clearing up the issue.
V2: fix typo. Also, this has been tested on GSPI and SDIO with V9 firmware.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power save support depends on the firmware capabilities rather than the
card's hardware interface. Use the FW_CAPINFO_PS bit in the firmware
capabilities mask throughout the driver in place of the redundant
ps_supported flag and don't make decisions about PS support in the
interface drivers (with the exception of a special case in the USB
driver).
V2: put the USB special case in the right place.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
Many developers use "/debug/" or "/debugfs/" or "/sys/kernel/debug/"
directory name to mount debugfs filesystem for ftrace according to
./Documentation/tracers/ftrace.txt file.
And, three directory names(ex:/debug/, /debugfs/, /sys/kernel/debug/) is
existed in kernel source like ftrace, DRM, Wireless, Documentation,
Network[sky2]files to mount debugfs filesystem.
debugfs means debug filesystem for debugging easy to use by greg kroah
hartman. "/sys/kernel/debug/" name is suitable as directory name
of debugfs filesystem.
- debugfs related reference: http://lwn.net/Articles/334546/
Fix inconsistency of directory name to mount debugfs filesystem.
* From Steven Rostedt
- find_debugfs() and tracing_files() in this patch.
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by : Inaky Perez-Gonzalez <inaky@linux.intel.com>
Reviewed-by : Steven Rostedt <rostedt@goodmis.org>
Reviewed-by : James Smart <james.smart@emulex.com>
CC: Jiri Kosina <trivial@kernel.org>
CC: David Airlie <airlied@linux.ie>
CC: Peter Osterlund <petero2@telia.com>
CC: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
CC: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
CC: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We're going to remove the FIRMWARE_NAME_MAX definition in order to avoid any
firmware name length restriction.
This patch eplaces the shared FIRMWARE_NAME_MAX definition with a libertas
local one.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The card firmware does not set the Command Download Ready interrupt bit
when IEEE PS mode is enabled, preventing the driver from sending
commands (such as the command to exit IEEE PS mode) since there is no
indication that the card is ready to accept commands.
This patch works around the problem by using the the TX Download Ready
bit in place of the Command Download Ready Bit while in IEEE PS mode.
TX Download Ready is set in IEEE PS mode.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the dependency on GPIO framework and lets the SPI host
driver handle the chip select. The SPI host driver is required to keep
the CS active for the entire message unless cs_change says otherwise.
This patch collects the two/three single SPI transfers into a message.
Also the delay in read path in case use_dummy_writes are not used is
moved into the SPI host driver.
Tested-by: Mike Rapoport <mike@compulab.co.il>
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is to incorporate Dan Williams' comments for commit:
"libertas: implement function init/shutdown commands for SD8688"
1. remove fn_init_required and fn_shutdown_required variables from
lbs_private structure. If required, __lbs_cmd() will be called
directly to send function init/shutdown command for SD8688 in
if_sdio_probe() or if_sdio_remove() callback.
2. add global variable "user_rmmod" to distinguish between the module
removal case and the card removal case. This flag will be checked in
if_sdio_remove() against SD8688 card to determine whether or not the
function shutdown command needs to be sent.
3. remove "card" from if_sdio_model structure as it cannot store
card pointers for multiple cards. Besides, it's no longer needed
to store the "card" pointer with changes #1 & #2 above.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oddly enough, the firmware's JOIN/START commands don't appear to have
any facility for setting custom IEs, thus the started adhoc network
doesn't advertise its WPA capability in the beacon. Whee!
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And fix up setting authentication suite for v9+ firmware too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Easier to read and more conformant with kernel style.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some of the parameters for association/join/start commands aren't
used (like the FH and CF IEs for IBSS, and the FH IE for BSS), so
get rid of their unions to reduce indirection. Also clean up
structure names for kernel style.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment (which I remove) says that the translation is done SPI routines.
IMHO this can't work because the SPI driver does not know whether the incomming
bytes are part of the registers/bytes which need to be flipped or part of
packet data which has to remain untouched.
While adding le helpers I also removed spu_write_u32() which has no users.
Tested-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The scratch pad register is used to store firmware status after
firmware is downloaded and initialized. After firmware status is
verified OK, the same register is used to store RX packet length.
Hence the firmware status code is no longer valid afterwards.
SD8688 firmware introduces a new register for firmware status
which will never be overwritten.
Also add scratch_reg variable to if_sdio_card structure and
initialize it based on the model of the card during probe.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SD8688 is a WLAN/Bluetooth combo chip and both functions are supported
in a single firmware image. FUNC_INIT and FUNC_SHUTDOWN commands are
implemented to utilize the multiple function feature.
When SD8688 card is inserted, the firmware image should be downloaded
only once through either WLAN function (Libertas driver) or Bluetooth
function (Bluetooth driver).
This patch adds function init/shutdown for SD8688 WLAN function only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usually, the 16-bit rx length is read from scratch pad registers
with two CMD52 transactions:
SD8385: IF_SDIO_SCRATCH_OLD (0x80fe/0x80ff)
SD8686/SD8688: IF_SDIO_SCRATCH (0x34/0x35)
Alternatively, SD8688 firmware offers an enhanced method for driver
to read an 8-bit rx length (in units) with a single CMD52:
IF_SDIO_RX_UNIT 0x43 is read one time after firmware is ready.
IF_SDIO_RX_LEN 0x42 is read every time when rx interrupt is received.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
replace direct usages of SDIO model numbers with defined macros.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The GPSI interface driver does not re-enable the Card Event Interrupt, which
causes problems after a card event (for example: link-loss) comes in. This
can lead, for example, to the card failing to re-associate. This patch
ensures that we re-enable the Card Event Interrupt when we handle card events.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/if_spi.c: In function ‘if_spi_c2h_data’:
drivers/net/wireless/libertas/if_spi.c:733: warning: format ‘%u’ expects type ‘unsigned int’, but argument 4 has type ‘long unsigned int’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A detection function was added for identifying CF8381.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/libertas/rx.c: In function ‘lbs_process_rxed_packet’:
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 4 has type ‘__le32’
drivers/net/wireless/libertas/rx.c:184: warning: format ‘%zd’ expects type ‘signed size_t’, but argument 5 has type ‘unsigned int’
Signed-off-by: John W. Linville <linville@tuxdriver.com>
libertas: add support for Marvell SD8688 chip
Use RxPD->pkt_ptr to locate eth803 header in the packet
received since SD8688/v10 firmware allows a gap between
RxPD and eth803 header.
Set SDIO block size to 256 for CMD53.
The maximum block size for SD8688 WLAN function is set
to 512 in TPLFE_MAX_BLK_SIZE. But using 512 as block size
results upto 2K bytes data (4 blocks) being transferred
and causes buffer overflow in firmware.
Both changes above are backward compatible with earlier
firmware versions for SD8385/SD8686.
The SDIO_DEVICE_IDs for SD8688 chip are added in
include/linux/mmc/sdio_ids.h
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the libertas main thread contends with the spi driver thread
in the TX path. To improve throughput, ensure that the driver thread
has higher scheduling priority than the libertas main thread. Do this
by making the libertas spi driver thread a low priority real time
thread.
We measured an average throughput improvement of 13%.
Signed-off-by: Anna Neal <anna@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CMD_MESH_CONFIG command ID and a couple of structure members in TxPD,
RxPD have been changed in firmware version 10.x.y.z and newer.
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't lead memory when receive errors
Signed-off-by: Philip Rakity <prakity@yahoo.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Radiotap was updated to include a "bad PLCP" flag and standardise
the "bad FCS" flag in the "flags" rather than "RX flags" field,
this patch updates Linux to that standard.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The libertas SDIO interface scheduled the packet worker, resulting in
unwanted latency for every data packet or command sent to the firmware.
Fix a bug on the SDIO probe error path too.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The problem: "iwconfig ethX power on" returns error
The cause: "ps_supported" flag was never set for SD8385/8686
The fix: check firmware capabilities returned by GET_HW_SPEC command.
Set "ps_supported" to 1 if FW_CAPINFO_PS bit is on. This fix applies
to SDIO interface only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mesh and radiotap interfaces need to use the same private data as
the main wifi interface. If the main wifi interface uses netdev_priv(),
but the other interfaces ->ml_priv, there's no way to figure out where
the private data actually is in the WEXT handlers and netdevice
callbacks. So make everything use ->ml_priv.
Fixes botched netdev_priv() conversion introduced by "netdevice
libertas: Fix directly reference of netdev->priv", though admittedly
libertas' use of ->priv was somewhat "special".
Signed-off-by: Kiran Divekar <dkiran@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pos[4] can't be both 0x43 and 0x04, 2nd should be pos[5]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In certain cases it is required to perform board specific actions
before activating libertas G-SPI interface. These actions may include
power up of the chip, GPIOs setup, proper pin-strapping and SPI
controller config.
This patch adds ability to call board specific setup/teardown methods
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
if_cs_poll_while_fw_download() returned the number of iterations
remaining on success, which in turn got returned as the value from
if_cs_prog_real() and if_cs_prog_helper(). But since if_cs_probe()
interprets non-zero return values from firmware load functions as an
error, this sometimes caused spurious firmware load failures.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add initial support for libertas devices using a GSPI interface. This has
been tested with the 8686.
GSPI is intended to be used on embedded systems. Board-specific parameters are
required (see libertas_spi.h).
Thanks to everyone who took a look at the earlier versions of the patch.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add GSPI constants to libertas core.
Fix misleading comment in lbs_setup_firmware.
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Data structures that come over the wire from the WLAN firmware must be packed.
This fixes alignment problems on the blackfin architecture and, reportedly, on
the AVR32.
This is a replacement for the previous version of this patch which had also
explicitly used get_unaligned_ macros. As Johannes Berg pointed out, these
macros were unnecessary.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: Colin McCabe <colin@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
