594632efbb
OMAP4430 supports UTMI and ULPI types of transceiver interface. In UTMI mode: The PHY is embedded within OMAP4430. The transceiver functionality is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY functionality is embedded within the OMAP4430. There is no direct interactions between the MUSB controller and TWL6030 chip to communicate the session-valid, session-end and ID-GND events. It has to be done through a software by setting/resetting bits in one of the control module register of OMAP4430 which in turn toggles the appropriate signals to MUSB controller. musb driver is register for blocking notifications from the transceiver driver to get the event notifications for connect/disconnect and ID-GND. Based on these events call the transceiver init/shutdown function to configure the transceiver to toggle the VBUS valid, session end and ID_GND signals to musb and power on/off the internal PHY. For ID_GND event notifications, toggle the ID_GND signal and then wait for musb to be configured as "A" device, and then call the transceiver function to set the VBUS. In OTG mode and musb as a host, When the Micro A connector used, VBUS is turned on and session bit set. When the device is connected, enumeration goes through. When the device disconnected from the other end of the connector(ID is still grounded), link will detect the disconnect and end the session. When the device is connected back, there are no events generated in the TWL6030-usb, and link is already down. So the device is not detected. Removed the session bit disable code which will recognize the connect of the device. Limitation: In OTG host mode, if device is connected during boot, it does not get detected. If disconnect and connect it back or connect after boot only it works. Fix for this, I will submit seperate patch later. Signed-off-by: Hema HK <hemahk@ti.com> Signed-off-by: Felipe Balbi <balbi@ti.com> |
||
|---|---|---|
| .. | ||
| atm | ||
| c67x00 | ||
| class | ||
| core | ||
| early | ||
| gadget | ||
| host | ||
| image | ||
| misc | ||
| mon | ||
| musb | ||
| otg | ||
| serial | ||
| storage | ||
| wusbcore | ||
| Kconfig | ||
| Makefile | ||
| README | ||
| usb-skeleton.c | ||
To understand all the Linux-USB framework, you'll use these resources:
* This source code. This is necessarily an evolving work, and
includes kerneldoc that should help you get a current overview.
("make pdfdocs", and then look at "usb.pdf" for host side and
"gadget.pdf" for peripheral side.) Also, Documentation/usb has
more information.
* The USB 2.0 specification (from www.usb.org), with supplements
such as those for USB OTG and the various device classes.
The USB specification has a good overview chapter, and USB
peripherals conform to the widely known "Chapter 9".
* Chip specifications for USB controllers. Examples include
host controllers (on PCs, servers, and more); peripheral
controllers (in devices with Linux firmware, like printers or
cell phones); and hard-wired peripherals like Ethernet adapters.
* Specifications for other protocols implemented by USB peripheral
functions. Some are vendor-specific; others are vendor-neutral
but just standardized outside of the www.usb.org team.
Here is a list of what each subdirectory here is, and what is contained in
them.
core/ - This is for the core USB host code, including the
usbfs files and the hub class driver ("khubd").
host/ - This is for USB host controller drivers. This
includes UHCI, OHCI, EHCI, and others that might
be used with more specialized "embedded" systems.
gadget/ - This is for USB peripheral controller drivers and
the various gadget drivers which talk to them.
Individual USB driver directories. A new driver should be added to the
first subdirectory in the list below that it fits into.
image/ - This is for still image drivers, like scanners or
digital cameras.
../input/ - This is for any driver that uses the input subsystem,
like keyboard, mice, touchscreens, tablets, etc.
../media/ - This is for multimedia drivers, like video cameras,
radios, and any other drivers that talk to the v4l
subsystem.
../net/ - This is for network drivers.
serial/ - This is for USB to serial drivers.
storage/ - This is for USB mass-storage drivers.
class/ - This is for all USB device drivers that do not fit
into any of the above categories, and work for a range
of USB Class specified devices.
misc/ - This is for all USB device drivers that do not fit
into any of the above categories.