63aed85e35
The WM831x backlight driver requires at least the specification of the current sink to use and a maximum current to allow them to function and will actively interfere with other users of the regulators it uses if misconfigured so only register the subdevice for it if this platform data has been supplied. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
114 lines
3.3 KiB
C
114 lines
3.3 KiB
C
/*
|
|
* include/linux/mfd/wm831x/pdata.h -- Platform data for WM831x
|
|
*
|
|
* Copyright 2009 Wolfson Microelectronics PLC.
|
|
*
|
|
* Author: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
*
|
|
*/
|
|
|
|
#ifndef __MFD_WM831X_PDATA_H__
|
|
#define __MFD_WM831X_PDATA_H__
|
|
|
|
struct wm831x;
|
|
struct regulator_init_data;
|
|
|
|
struct wm831x_backlight_pdata {
|
|
int isink; /** ISINK to use, 1 or 2 */
|
|
int max_uA; /** Maximum current to allow */
|
|
};
|
|
|
|
struct wm831x_backup_pdata {
|
|
int charger_enable;
|
|
int no_constant_voltage; /** Disable constant voltage charging */
|
|
int vlim; /** Voltage limit in milivolts */
|
|
int ilim; /** Current limit in microamps */
|
|
};
|
|
|
|
struct wm831x_battery_pdata {
|
|
int enable; /** Enable charging */
|
|
int fast_enable; /** Enable fast charging */
|
|
int off_mask; /** Mask OFF while charging */
|
|
int trickle_ilim; /** Trickle charge current limit, in mA */
|
|
int vsel; /** Target voltage, in mV */
|
|
int eoc_iterm; /** End of trickle charge current, in mA */
|
|
int fast_ilim; /** Fast charge current limit, in mA */
|
|
int timeout; /** Charge cycle timeout, in minutes */
|
|
};
|
|
|
|
/* Sources for status LED configuration. Values are register values
|
|
* plus 1 to allow for a zero default for preserve.
|
|
*/
|
|
enum wm831x_status_src {
|
|
WM831X_STATUS_PRESERVE = 0, /* Keep the current hardware setting */
|
|
WM831X_STATUS_OTP = 1,
|
|
WM831X_STATUS_POWER = 2,
|
|
WM831X_STATUS_CHARGER = 3,
|
|
WM831X_STATUS_MANUAL = 4,
|
|
};
|
|
|
|
struct wm831x_status_pdata {
|
|
enum wm831x_status_src default_src;
|
|
const char *name;
|
|
const char *default_trigger;
|
|
};
|
|
|
|
struct wm831x_touch_pdata {
|
|
int fivewire; /** 1 for five wire mode, 0 for 4 wire */
|
|
int isel; /** Current for pen down (uA) */
|
|
int rpu; /** Pen down sensitivity resistor divider */
|
|
int pressure; /** Report pressure (boolean) */
|
|
int data_irq; /** Touch data ready IRQ */
|
|
};
|
|
|
|
enum wm831x_watchdog_action {
|
|
WM831X_WDOG_NONE = 0,
|
|
WM831X_WDOG_INTERRUPT = 1,
|
|
WM831X_WDOG_RESET = 2,
|
|
WM831X_WDOG_WAKE = 3,
|
|
};
|
|
|
|
struct wm831x_watchdog_pdata {
|
|
enum wm831x_watchdog_action primary, secondary;
|
|
int update_gpio;
|
|
unsigned int software:1;
|
|
};
|
|
|
|
#define WM831X_MAX_STATUS 2
|
|
#define WM831X_MAX_DCDC 4
|
|
#define WM831X_MAX_EPE 2
|
|
#define WM831X_MAX_LDO 11
|
|
#define WM831X_MAX_ISINK 2
|
|
|
|
struct wm831x_pdata {
|
|
/** Called before subdevices are set up */
|
|
int (*pre_init)(struct wm831x *wm831x);
|
|
/** Called after subdevices are set up */
|
|
int (*post_init)(struct wm831x *wm831x);
|
|
|
|
int gpio_base;
|
|
struct wm831x_backlight_pdata *backlight;
|
|
struct wm831x_backup_pdata *backup;
|
|
struct wm831x_battery_pdata *battery;
|
|
struct wm831x_touch_pdata *touch;
|
|
struct wm831x_watchdog_pdata *watchdog;
|
|
|
|
/** LED1 = 0 and so on */
|
|
struct wm831x_status_pdata *status[WM831X_MAX_STATUS];
|
|
/** DCDC1 = 0 and so on */
|
|
struct regulator_init_data *dcdc[WM831X_MAX_DCDC];
|
|
/** EPE1 = 0 and so on */
|
|
struct regulator_init_data *epe[WM831X_MAX_EPE];
|
|
/** LDO1 = 0 and so on */
|
|
struct regulator_init_data *ldo[WM831X_MAX_LDO];
|
|
/** ISINK1 = 0 and so on*/
|
|
struct regulator_init_data *isink[WM831X_MAX_ISINK];
|
|
};
|
|
|
|
#endif
|