A future version of the MPC8610 HPCD's ASoC DMA driver will probe on individual
DMA channel nodes, so the DMA controller nodes' compatible string must be listed
in mpc8610_ids[] for the probe to work.
Also remove the "gianfar" compatible from mpc8610_ids[], since there is no
gianfar (or any other networking device) on the 8610.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are two front-panel LEDs on MPC837xRDB and MPC8315RDB boards: PWR
and HDD. After adding appropriate nodes we can program these LEDs from
kernel and user space.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since USB2 is shared with local bus, either local bus or USB2
should be disabled. By default U-Boot enables local bus, so we
have to disable USB2, otherwise kernel hangs:
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
<hangs here>
Note that U-Boot doesn't clear 'status' property when it enables
USB2, so we have to comment out the whole node.
To enable USB2, one can issue
'setenv hwconfig usb2:dr_mode=<host|peripheral>' command at the
U-Boot prompt.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for eTSEC 2.0 as found in P1020.
The changes include introduction of the group nodes for
the etsec nodes.
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Technically, whilst SEC v3.3 h/w honours the tls_ssl_stream descriptor
type, it lacks the ARC4 algorithm execution unit required to be able
to execute anything meaningful with it. Change the node to agree with
the documentation that declares that the sec3.3 really doesn't have such
a descriptor type.
Reported-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable the DEBUG_PER_CPU_MAPS option so we can look for problems with
cpumasks .
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert to the new cpumask API.
irq_choose_cpu can be simplified by using cpumask_next and cpumask_first.
smp_mpic_message_pass was doing open coded cpumask manipulation and passing an
int for a cpumask into mpic_send_ipi. Since mpic_send_ipi is only used
locally, make it static and convert it to take a cpumask. This allows us
to clean up the mess in smp_mpic_message_pass.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the *_map cpumask variants are deprecated, change the comments to
instead refer to *_mask.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert NUMA code to new cpumask API. We shift the node to cpumask
setup code until after we complete bootmem allocation so we can
dynamically allocate the cpumasks.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert hotplug-cpu code to new cpumask API.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Dynamically allocate cpu_sibling_map and cpu_core_map cpumasks.
We don't need to set_cpu_online() the boot cpu in smp_prepare_boot_cpu,
init/main.c does it for us.
We also postpone setting of the boot cpu in cpu_sibling_map and cpu_core_map
until when the memory allocator is available (smp_prepare_cpus), similar
to x86.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask API in /proc/cpuinfo code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This separates the per cpu output from the summary output at the end of the
file, making it easier to convert to the new cpumask API in a subsequent
patch.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new cpumask API and add some comments to clarify how get_irq_server
works.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask functions in pseries SMP startup code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask functions in iseries SMP startup code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use new cpumask_* functions, and dynamically allocate cpumask in fixup_irqs.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use the new cpumask_* functions and dynamically allocate the cpumask in
smp_cpus_done.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Use cpumask_first, cpumask_next in rtasd code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Change &cpu_online_map to cpu_online_mask.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
As explained in commit 1c0fe6e3bd, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.
Cc: linuxppc-dev@ozlabs.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We need to keep track of the backing pages that get allocated by
vmemmap_populate() so that when we use kdump, the dump-capture kernel knows
where these pages are.
We use a simple linked list of structures that contain the physical address
of the backing page and corresponding virtual address to track the backing
pages.
To save space, we just use a pointer to the next struct vmemmap_backing. We
can also do this because we never remove nodes. We call the pointer "list"
to be compatible with changes made to the crash utility.
vmemmap_populate() is called either at boot-time or on a memory hotplug
operation. We don't have to worry about the boot-time calls because they
will be inherently single-threaded, and for a memory hotplug operation
vmemmap_populate() is called through:
sparse_add_one_section()
|
V
kmalloc_section_memmap()
|
V
sparse_mem_map_populate()
|
V
vmemmap_populate()
and in sparse_add_one_section() we're protected by pgdat_resize_lock().
So, we don't need a spinlock to protect the vmemmap_list.
We allocate space for the vmemmap_backing structs by allocating whole pages
in vmemmap_list_alloc() and then handing out chunks of this to
vmemmap_list_populate().
This means that we waste at most just under one page, but this keeps the code
is simple.
Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Sean MacLennan <smaclennan@pikatech.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Ben Dooks <ben-linux@fluff.org>
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Drop NO_IRQ as 0 is the preferred way to describe 'no irq'
(http://lkml.org/lkml/2005/11/21/221). This change is safe, as the driver is
only used on powerpc, where NO_IRQ is 0 anyhow.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the parsing of the device tree in
arch/powerpc/include/asm/parport.h assumes that the interrupt provided in
the parallel port node is a valid virtual irq. The values for the
interrupts provided in the device tree should have meaning in the context
of the driver for the specific interrupt controller to which the interrupt
is connected and irq_of_parse_and_map() should be used to determine the
correct virtual irq.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So we tried to speed things up a bit using flush_hash_pages() directly
but that falls over on 603 of course meaning we fail to flush the TLB
properly and we may even end up having it corrupt memory randomly by
accessing a hash table that doesn't exist.
This removes the "optimization" by always going through flush_tlb_page()
for now at least.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we always call start-cpu irrespective of if the CPU is
stopped or not. Unfortunatley on POWER7, firmware seems to not like
start-cpu being called when a cpu already been started. This was not
the case on POWER6 and earlier.
This patch checks to see if the CPU is stopped or not via an
query-cpu-stopped-state call, and only calls start-cpu on CPUs which
are stopped.
This fixes a bug with kexec on POWER7 on PHYP where only the primary
thread would make it to the second kernel.
Reported-by: Ankita Garg <ankita@linux.vnet.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This moves query_cpu_stopped() out of the hotplug cpu code and into
smp.c so it can called in other places and renames it to
smp_query_cpu_stopped().
It also cleans up the return values by adding some #defines
Cc: <stable@kernel.org>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
libata: Fix several inaccuracies in developer's guide
This patch fixes the bad hashes for one Kingston and one Transcend card.
Thanks to komuro for pointing this out.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit 6bfff31e77 (libata: kill probe_ent
and related helpers) killed ata_device_add() but didn't remove references
to it from the libata developer's guide.
Commits 9363c3825e (libata: rename SFF
functions) and 5682ed33aa (libata: rename
SFF port ops) renamed the taskfile access methods but didn't update the
developer's guide. Commit c9f75b04ed
(libata: kill ata_noop_dev_select()) didn't update the developer's
guide as well.
The guide also refers to the long gone ata_pio_data_xfer_noirq(),
ata_pio_data_xfer(), and ata_mmio_data_xfer() -- replace those by
the modern ata_sff_data_xfer_noirq(), ata_sff_data_xfer(), and
ata_sff_data_xfer32().
Also, remove the reference to non-existant ata_port_stop()...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Function init_kmem_cache_nodes is incorrect when checking upper limitation of
kmalloc_caches. The breakage was introduced by commit
91efd773c7 ("dma kmalloc handling fixes").
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
By setting "reset_type" to one of the following values, the default
software reset mechanism may be overidden. Here the possible values of
"reset_type":
1 - PPC4xx core reset
2 - PPC4xx chip reset
3 - PPC4xx system reset (default)
This will be used by a new PPC440SPe board port, which needs a "chip
reset" instead of the default "system reset" to be asserted.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
KEYS: call_sbin_request_key() must write lock keyrings before modifying them
KEYS: Use RCU dereference wrappers in keyring key type code
KEYS: find_keyring_by_name() can gain access to a freed keyring
A defconfig for the IBM ISS 476 simulator
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This is a trivial 4xx plaform that uses the new simple bsp from
Josh and is handy to use in simulators such as ISS or even Mambo
who don't properly implement most of the actual devices in the
SoC but really only the core.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
ALSA: take tu->qlock with irqs disabled
ALSA: hda: Use olpc-xo-1_5 quirk for Toshiba Satellite P500-PSPGSC-01800T
ALSA: hda: Use olpc-xo-1_5 quirk for Toshiba Satellite Pro T130-15F
ALSA: hda - fix array indexing while creating inputs for Cirrus codecs
ALSA: es968: fix wrong PnP dma index
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: joydev - allow binding to button-only devices
Input: elantech - ignore high bits in the position coordinates
Input: elantech - allow forcing Elantech protocol
Input: elantech - fix firmware version check
Input: ati_remote - add some missing devices from lirc_atiusb
Input: eeti_ts - cancel pending work when going to suspend
Input: Add support of Synaptics Clickpad device
Revert "Input: ALPS - add signature for HP Pavilion dm3 laptops"
Input: psmouse - ignore parity error for basic protocols
The raid6 recovery code should immediately drop back to the optimized
synchronous path when a p+q dma resource is not available. Otherwise we
run the non-optimized/multi-pass async code in sync mode.
Verified with raid6test (NDISKS=255)
Applies to kernels >= 2.6.32.
Cc: <stable@kernel.org>
Acked-by: NeilBrown <neilb@suse.de>
Reported-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
476 requires an isync after loading MMU and debug related SPR's. Some of
these are in performance-critical paths and may need to be optimized, but
initially, we're playing it safe.
Signed-off-by: Torez Smith <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
call_sbin_request_key() creates a keyring and then attempts to insert a link to
the authorisation key into that keyring, but does so without holding a write
lock on the keyring semaphore.
It will normally get away with this because it hasn't told anyone that the
keyring exists yet. The new keyring, however, has had its serial number
published, which means it can be accessed directly by that handle.
This was found by a previous patch that adds RCU lockdep checks to the code
that reads the keyring payload pointer, which includes a check that the keyring
semaphore is actually locked.
Without this patch, the following command:
keyctl request2 user b a @s
will provoke the following lockdep warning is displayed in dmesg:
===================================================
[ INFO: suspicious rcu_dereference_check() usage. ]
---------------------------------------------------
security/keys/keyring.c:727 invoked rcu_dereference_check() without protection!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by keyctl/2076:
#0: (key_types_sem){.+.+.+}, at: [<ffffffff811a5b29>] key_type_lookup+0x1c/0x71
#1: (keyring_serialise_link_sem){+.+.+.}, at: [<ffffffff811a6d1e>] __key_link+0x4d/0x3c5
stack backtrace:
Pid: 2076, comm: keyctl Not tainted 2.6.34-rc6-cachefs #54
Call Trace:
[<ffffffff81051fdc>] lockdep_rcu_dereference+0xaa/0xb2
[<ffffffff811a6d1e>] ? __key_link+0x4d/0x3c5
[<ffffffff811a6e6f>] __key_link+0x19e/0x3c5
[<ffffffff811a5952>] ? __key_instantiate_and_link+0xb1/0xdc
[<ffffffff811a59bf>] ? key_instantiate_and_link+0x42/0x5f
[<ffffffff811aa0dc>] call_sbin_request_key+0xe7/0x33b
[<ffffffff8139376a>] ? mutex_unlock+0x9/0xb
[<ffffffff811a5952>] ? __key_instantiate_and_link+0xb1/0xdc
[<ffffffff811a59bf>] ? key_instantiate_and_link+0x42/0x5f
[<ffffffff811aa6fa>] ? request_key_auth_new+0x1c2/0x23c
[<ffffffff810aaf15>] ? cache_alloc_debugcheck_after+0x108/0x173
[<ffffffff811a9d00>] ? request_key_and_link+0x146/0x300
[<ffffffff810ac568>] ? kmem_cache_alloc+0xe1/0x118
[<ffffffff811a9e45>] request_key_and_link+0x28b/0x300
[<ffffffff811a89ac>] sys_request_key+0xf7/0x14a
[<ffffffff81052c0b>] ? trace_hardirqs_on_caller+0x10c/0x130
[<ffffffff81394fb9>] ? trace_hardirqs_on_thunk+0x3a/0x3f
[<ffffffff81001eeb>] system_call_fastpath+0x16/0x1b
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
The keyring key type code should use RCU dereference wrappers, even when it
holds the keyring's key semaphore.
Reported-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
