Multiple iwlagn based devices shared the same hcmd related functions.
Move from iwl-5000.c to iwl-agn-hcmd.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Loading uCode functions are shared across multiple agn devices.
Move those functions to iwl-agn-ucode.c file with other uCode
related functions.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Multiple iwlagn based devices shared the same ucode loading procedure.
Move loading related code from iwl-5000.c to iwl-agn-ucode.c file.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
iwl_good_ack_health() check for expected and actual ack count which only
apply to aggregation mode. Move the function to iwlagn module.
Reported-by: Chantry Xavier <chantry.xavier@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
This reverts commit 76232ebf89.
iwl_good_ack_health only applies to aggregation and thus only to iwlagn. We
can thus move the function to iwlagn instead of modifying compile flags.
This is done in following patch.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
drivers/net/wireless/iwlwifi/iwl-rx.c: In function 'iwl_good_ack_health':
drivers/net/wireless/iwlwifi/iwl-rx.c:647: error: 'struct iwl_priv' has no member named '_agn'
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In nl80211.h, be a little more elaborate in the docs for the definitions
NL80211_ATTR_CQM_RSSI_THOLD and NL80211_ATTR_CQM_RSSI_HYST.
Reported-by: Luis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for the set_cqm_config op. This op function configures the
requested connection quality monitor rssi threshold and rssi hysteresis
values to the hardware if the hardware supports
IEEE80211_HW_SUPPORTS_CQM.
For unsupported hardware, currently -EOPNOTSUPP is returned, so the mac80211
is currently not doing connection quality monitoring on the host. This could be
added later, if needed.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for basic configuration of a connection quality monitoring to the
nl80211 interface, and basic support for notifying about triggered monitoring
events.
Via this interface a user-space connection manager may configure and receive
pre-warning events of deteriorating WLAN connection quality, and start
preparing for roaming in advance, before the connection is already lost.
An example usage of such a trigger is starting scanning for nearby AP's in
an attempt to find one with better connection quality, and associate to it
before the connection characteristics of the existing connection become too bad
or the association is even lost, leading in a prolonged delay in connectivity.
The interface currently supports only RSSI, but it could be later extended
to include other parameters, such as signal-to-noise ratio, if need for that
arises.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Auto auth mode is enabled by default. If user doesn't specify the
auth mode, while association driver will first try with open mode
and then with shared key mode. If user specifies an auth mode,
auto auth is disabled and driver will not try association with
another auth mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on a RFC patch by Kalle Valo.
The wl1271 has a feature which handles the connection monitor logic
in hardware, basically sending periodically nullfunc frames and reporting
to the host if AP is lost, after attempting to recover by sending
probe-requests to the AP.
Add support to mac80211 by adding a new flag IEEE80211_HW_CONNECTION_MONITOR
which prevents conn_mon_timer from triggering during idle periods, and
prevents sending probe-requests to the AP if beacon-loss is indicated by the
hardware.
Cc: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change local functions that are cast to iw_handler to
the more standard use with "union iwreq_data *wrqu"
so the iw_handler array no longer needs the casts.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert direct uses of [ (foo - SIOCIWFIRST) , fn)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a wireless.h macro for this, might as well use it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a wireless.h macro for this, might as well use it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These two #defines use the same value, but
SIOCIWFIRST makes more sense in this use.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Removing the wl1271 from the inet addr notifier chain sometimes causes the
registered handler to be called - causing locking problems if the removing
function is called from within the mutex.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes MAC address handling. To achieve this, firmware booting had
to be delayed from the previous op_start to op_add_interface, which is the point
when the driver gets to know the configured MAC address. As the wl1271 only
supports one virtual interface, this even seems quite logical.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add configuration values for the varous WLAN-BT co-ex configuration parameters,
and finally enable WLAN-BT co-ex. Based on preliminary measurements, it
appears the co-ex feature is not increasing WLAN power consumption, if BT
is not activated.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9271 needs a full reset only upon the first reset, add
a call for the driver to enable these special resets. We
can optimize this out later without an export.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When initializing the PLL on AR9271 we always need
to set the core clock to 117MHz. While at it remove
the baud rate settings for the serial device on the
AR9271, the default settings work well unless you
want to customize it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noisefloor calibration involves querying hardware for samples
and storing this information on a history buffer in hardware for
actual noisefloor calibration processing in hardware. The history
buffer supports collecting information for all Atheros hardware,
one history buffer slot for each chain on each channel used for
MIMO operation. For current hardware this means one history
buffer slot for each chain on both the control (or primary) channel
and the extension (or secondary) channel. We know which noisefloor
registers to poke for collecting noisefloor data through the
chainmask.
For AR9285 and AR9271 devices, both 1x1, the chaimmask is defined as
0x9 = 0b0001001. The first four bits represent each chain out of
a maximum of 4 chains [0-3] on the primary channel. The last four
bits represent each chain on the extension channel. A chainmask
of 0x9 therefore indicates chain 1 is active on both the primary
and the extension channel.
AR9271 only requires collecting and storing noisefloor history buffer
data for the first chain on both the control and extension channel
(nfarray[0] and nfarray[3]) so fix the code and avoid which reads
and writes to the history buffer for the other chains.
Since the noisefloor varies depending on the number of chains your
device supports also initialize the noisefloor history buffer with
reasonable values seen on 1x1 devices such as AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
