This patch resets the cmd timer if cmds started before
the timedout command are making progress. The idea is
that the cmd probably timed out because we are trying
to exeucte too many commands. If it turns out that the
device the IO timedout on was bad or the cmd just got
screwed up but other IO/devs were ok then we will
will figure this out when the cmds ahead of the timed
out one complete ok.
This also fixes a bug where we were sort of detecting
this by setting the last_timeout and last_xfer to the
same value when the task was allocated. That caught
the case where we never got to send any IO for it. However,
if the problem had started right before we started the
new task, then we were forced to wait an extra cmd
timeout seconds to start the scsi eh.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the netdev has not been setup when the host is, we will oops when
the iscsi layer calls into the driver and a it tries to reference the
netdev in hba->ndev.
This can happen if the iscsi driver is loaded before ifup is
done. This patch just adds a check, so we can gracefully fail the
operation.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After discussing this patch with LSI, I resubmitting with a recommended
40 second wait for the alternate ioc's initialization to complete.
--
Fusion FC chips are two function with some shared resources. During
initialization of one function its driver inhibits the ability of the
other function's driver to allocate message frames by clearing its
"active" flag. Should mid-layer error recovery be initiated for a
scsi command during this initialization (which can take up to 40 seconds)
error recovery will escalate to the level of host reset. This host
reset might fail (as the other function is resetting) resulting in
all connected targets being taken offline.
This patch holds off mid-layer error recovery for up to 40 seconds
to permit initialization of the other function to complete.
Signed-off-by: Michael Reed <mdr@sgi.com>
Acked-by: "Desai, Kashyap" <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The use of the big kernel lock here appears
to be ancient cruft that is no longer needed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
fix bug in adjust_hpsa_scsi_table which caused devices which have
changed size, etc. to do the wrong thing.
The problem was as follows:
The driver maintains its current idea of what devices are present
in the h->dev[] array. When it updates this array, it scans the
hardware, and produces a new list of devices, call it sd[], for
scsi devices.
Then, it compares each item in h->dev[] vs. sd[], and any items which
are not present sd it removes from h->dev[], and any items present
in sd[], but different, it modifies in h->dev[].
Then, it looks for items in sd[] which are not present in h->dev[],
and adds those items into h->dev[]. All the while, it keeps track
of what items were added and removed to/from h->dev[].
Finally, it updates the SCSI mid-layer by removing and adding
the same devices it removed and added to/from h->dev[]. (modified
devices count as a remove then add.)
originally, when a "changed" device was discovered, it was
removed then added to h->dev[]. The item was added to the *end*
of h->dev[]. And, the item was removed from sd[] as well
(nulled out). As it processed h->dev[], these newly added items
at the end of the list were encountered, and sd[] was searched,
but those items were nulled out. So they ended up getting removed
immediately after they were added.
The solution is to have a way to replace items in the h->dev[]
array instead of doing a remove + add. Then the "changed" items.
are not encountered a second time, and removed.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
use scan_start and scan_finished entry points for scanning and route
the CCISS_REGNEWD ioctl and sysfs triggering of same functionality
through hpsa_scan_start.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The p1210m responsds to SCSI report LUNs, unlike traditional Smart
Array controllers. This means that the bus, target, and lun
assignments done by the driver cannot be arbitrary, but must match
what SCSI REPORT LUNS returns.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is done by adding support for the so-called "performant mode"
(that's really what they called it). Smart Array controllers
have a mode which enables multiple command completions to be
delivered with a single interrupt, "performant" mode. We want to use
that mode, as some newer controllers will be requiring this mode.
Signed-off-by: Don Brace <brace@beardog.cce.hp.com>
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
driver fixed the device update issue after get the AEN PD delete/ADD
and LD add/delete from FW.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver issue the get ld list to fw to get the logic drive list.
Driver will keep the logic drive list for the internal use after
driver load.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add the pad_0 in mfi frame structure to 0 to fix the context value
larger than 32bit value issue.
Signed-off-by Bo Yang<bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Modify the following BSG commands to operate asynchronously.
- FC_BSG_RPT_ELS
- FC_BSG_RPT_CT
- LPFC_BSG_VENDOR_GET_CT_EVENT
- LPFC_BSG_VENDOR_SET_CT_EVENT
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Discovery relates changes:
- Separated VPI_REGISTERED state of physical port into VFI_REGISTERED and
VPI_REGISTERED state so that driver can unregister physical port VPI
independent of VFI.
- Add code to unregister, re-init and re-register physical port VPI
when physical port NportID change.
- Add code to unregister and re-register VPI of a vport when its Nport
ID change.
- Add code in FDISC completion path to re-start FLOGI discovery when
a FDISC complete with LOGIN_REQUIRED reason code.
- Fix a memory leak in lpfc_init_vpi_cmpl
- Add code to start a timer for vport to retry FDISC when CVL is received
by a vport or physical port. If all Nports receive CVLs, then all timers
are cancelled and a logical link level discovery will be started after
one second.
- Flush ELS commands after killing all delayed ELS commands.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix hardware/SLI relates issues:
- Handle XB bit so that ELS XRIs are not prematurely released.
- Handle XB bit so that FCP XRIs are not prematurely released.
- Define new security SLI Commands.
- Remove unused security SLI commands
- Skip receive data size parameter check on received FLOGI.
- Added LPFC_USE_FCPWQIDX flag to iocb to force SLI layer
to submit abort WQE on same WQ as the command WQE.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch corrects the chipopcode for text and chooses
correct paramters for that command
Signed-off-by: Jayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
