Add platform data necessary to support tmiofb on tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Take advantage of the newly created wm97xx battery driver
and remove useless code in mioa701 board code. Add also the
ac connection detect capability after the matching gpio was
discovered.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The charger enable gpio is straight (1 means draw from USB
Vbus, 0 mean do not draw). The USB Vbus sensing is inverted
(1 means no Vbus voltage sensed, 0 means Vbus voltage
present).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Change the halt and reboot method from gpio based to "jump
to ROM IPL beginning". This gives control back to IPL, which
without PowerOn key pressed, will put the device into deep
sleep until PowerOn is pressed for 1 second.
But this has the benefit of keeping the RTC registers across
reboots, which is good for OS change.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add GPIO configuration and platform specific declarations
to make Mitac Mio A701 camera chip work. The chip is a
Micron MT9M111 CMOS sensor, based on PXA QIF interface and
I2C bus for sensor control.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Since mioa701 board has migrated to the mfp architecture,
low power gpio setup is now correctly handled even when gpio
led driver is not loaded, and leds and vibrator don't stay
activated in suspend mode (especially vibrator).
Remove the not needed anymore dependency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add IO memory and IRQ ressources for pxa based SoC to be
able to use the new rtc-pxa driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Following the removal of the "->policy" usage for PXA255 in patch
459fc208ab (cpufreq: remove
policy->governor setting in drivers initialization), this patch
introduces an option (called "pxa255_turbo_table") to select either
the "run" or "turbo" frequency table.
It also cures the runtime warning that was printed each time the
frequency was changed.
Got rid of all references to CPUFREQ_POLICY_* for pxa255, and sticked
with the run/turbo thing.
Tested on an Arcom/Eurotech Viper.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This symbol is required by locomo backlight driver, exporting this
allows the driver to be built as a module.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN
bit, add their definitions here with comments.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
PXA935 has changed its implementor ID from Intel to Marvell, this
patch modifies arch/arm/boot/compressed/head.S and proc-xsc3.S to
support a smooth bootup.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Let's put these devices into a central place even if they are now
processor specific, as they might be re-used in later processors.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
There two are internal registers that are used to control the power
management of the Internal Memory (i.e. Internal SRAM). They are
referenced nowhere and removed here to simplify pxa-regs.h a bit.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
We now have generic PWM API for PXA, the PWM registers definitions are
now used nowhere, and it is not encouraged to manipulate them directly
by driver code.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
pxa_gpio_{get,set}_value() are not used anymore, remove them from hardware.h.
Declaration of pxa_gpio_mode() is still being referenced and thus moved into
pxa2xx-gpio.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Original patch from Marek Vasut, the problems with PXA26x are:
1. there are additional 4 GPIOs 86,87,88,89 have their direction bits
inverted in GPDR2, as well as their alternate function bits being
'1' for their GPIO functionality in GAFRx
2. there is no easy way to decide if the processor is a pxa26x or a
pxa250/pxa255 at run-time, so the assumption here is the pxa26x
will be treated as one of the pxa25x variants, and board code
should have a better knowledge of the processor it is featured
Introduce pxa26x_init_irq() for the second purpose, and treat the
additional GPIOs > 85 on PXA25x specially.
Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code
a bit when PXA26x support isn't needed. Board config options have
to select this to enable the support for PXA26x.
__gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x
isn't selected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This reverts commit da1a3dc0eb.
The originally proposed way in the above commit is incorrect. And
there is no easy way to distinguish between pxa25x and pxa26x at
run-time.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we
already have that variable, remove the unnecessary 'gpio_nr' now.
Also, fix the incorrect GPIO number passed in pxa27x_init_irq().
Note: pxa_last_gpio should be initialized earlier, and this is true
since it's been assigned in machine_desc->init_irq().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA SoC have several GPIOs muxed on only one wakeup source.
Add support for these wakeup sources which were missing
in mfp core support.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5330/1: mach-pxa: Fixup reset for systems using reboot=cold or other strings
[ARM] pxa: fix incorrect PCMCIA PSKTSEL pin configuration for spitz
[ARM] pxa: fix I2C controller device being registered twice on Akita
pxafb: only initialize the smart panel thread when dealing with a smartpanel
pxafb: introduce LCD_TYPE_MASK and use it.
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: ACE1001 patch for cp2101.c
USB: usbmon: fix read(2)
USB: gadget rndis: send notifications
USB: gadget rndis: stop windows self-immolation
USB: storage: update unusual_devs entries for Nokia 5300 and 5310
USB: storage: updates unusual_devs entry for the Nokia 6300
usb: musb: fix bug in musb_schedule
USB: fix SB700 usb subsystem hang bug
fix xen_get_eflags. It doesn't take any argument.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pv_cpu_ops.getreg(_IA64_REG_IP) returned constant.
But the returned ip valued should be the one in the caller, not of the callee.
This patch fixes that.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Tony Luck <tony.luck@intel.com>
arch/ia64/kernel/pci-dma.c only needs to include iommu once.
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Using printk from MCA/INIT context is unsafe since it can cause deadlock.
The ia64_mca_modify_original_stack is called from both of mca handler and
init handler, so it should use mprintk instead of printk.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Itanium processors can handle some misaligned data accesses. They
also provide a mode where all such accesses are forced to trap. The
kernel was schizophrenic about use of this mode:
* Base kernel code ran in permissive mode where the only traps
generated were from those cases that the h/w could not handle.
* Interrupt, syscall and trap code ran in strict mode where all
unaligned accesses caused traps to the 0x5a00 unaligned reference
vector.
Use strict alignment checking throughout the kernel, but make
sure that we continue to let user mode use more relaxed mode
as the default.
Signed-off-by: Tony Luck <tony.luck@intel.com>
When we migrate an interrupt from one CPU to another, we set the
move_in_progress flag and clean up the vectors later once they're not
being used. If you're unlucky and call destroy_irq() before the vectors
become un-used, the move_in_progress flag is never cleared, which causes
the interrupt to become unusable.
This was discovered by Jesse Brandeburg for whom it manifested as an
MSI-X device refusing to use MSI-X mode when the driver was unloaded
and reloaded repeatedly.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a regression reported by Max Kellermann whereby kernel profiling
showed that his clients were spending 45% of their time in
rpcauth_lookup_credcache.
It turns out that although his processes had identical uid/gid/groups,
generic_match() was failing to detect this, because the task->group_info
pointers were not shared. This again lead to the creation of a huge number
of identical credentials at the RPC layer.
The regression is fixed by comparing the contents of task->group_info
if the actual pointers are not identical.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Do not attempt to close invalidated file handles
[CIFS] fix check for dead tcon in smb_init
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
MIPS: csrc-r4k: Fix declaration depending on the wrong CONFIG_ symbol.
MIPS: csrc-r4k: Fix spelling mistake.
MIPS: RB532: Provide functions for gpio configuration
MIPS: IP22: Make indy_sc_ops variable static
MIPS: RB532: GPIO register offsets are relative to GPIOBASE
MIPS: Malta: Fix include paths in malta-amon.c
